Introduction
4 TVM Series Installation and Operation Handbook
Copyright © 2008, Harris Corporation
Video Input Options (supports two)
• TVM-VTM-AAP: The TVM-VTM-AAP is an advanced analysis package that
adds data analyzer functions in quadrant or full-screen views to the TVM-10.
Included in TVM-40.
• TVM-VTM-ASI: The TVM-VTM-ASI provides two passive-looping DVB-ASI
and SMPTE310 inputs. It accepts two independent MPEG streams and analyzes
one selected stream for compliance to measurement guidelines of ETSI TR-101-
290 (ETR-290) first, second, and third priority standards.
• TVM-VTM-SDI-H: The TVM-VTM-SDI-H provides two passive looping
SMPTE 292M (HD-SDI) and SMPTE 259M-C (SD-SDI) inputs, auto detect, line
select, internal, blackburst or tri-level references.
• TVM-VTM-SDI-S: The TVM-VTM-SDI-S provides two passive looping SMPTE
259M-C (SD-SDI) inputs, auto detect, and line select. Field upgradeable to HD
with the TVM-VTM-S2H-F.
• TVM-VTM S2H-F: The TVM-VTM S2H-F adds SMPTE 292M (HD-SDI) to
TVM-VTM SDI-S
• TVM-VTM-ACV-2: The TVM-VTM-ACV-2 is a dual composite analog input
module. Adds two composite analog passive looping inputs (NTSC or PAL) with
auto-detection and line select. Must be used as inputs C and D.
• TVM-VTM-EYE-S: The TVM-VTM-EYE-S provides two active looping SMPTE
259M-C (SD-SDI) inputs, auto detect with EYE pattern and monitor output. Field
upgradeable to HD with the TVM-VTM-ES2H-F.
• NOTE: The TVM-VTM-EYE-S must be used as inputs A and B.
• TVM-VTM-EYE-H: The TVM-VTM-EYE-H provides two active looping
SMPTE 292M (HD-SDI) and SMPTE 259M-C (SD-SDI) inputs, auto detect with
EYE pattern and monitor output.
NOTE: The TVM-VTM-EYE-H must be used as inputs A and B.
• TVM-VTM-ES2H-F: the TVM-VTM-ES2H-F adds SMPTE 292M (HD-SDI) to
the TVM-VTM-EYE-S module.
• TVM-VTM-JEM: The TVM-VTM-JEM provides two active looping SMPTE
292M (HD-SDI) and SMPTE 259M-C (SD-SDI) inputs, auto detect with EYE
pattern with advanced Jitter Analysis and monitor output.
NOTE: The TVM-VTM-JEM must be used as inputs A and B.
• TVM-VTM-DLK: The TVM-VTM-DLK expands the dual link capability of the
TVM-VTM-EYE-H, TVM-VTM-JEM, and TVM-VTM-SDI-H to include 10-bit
RGB (4:4:4) and RGB+A (4:4:4:4) formats.
NOTE: The TVM-VTM-DLK requires the TVM-40.
• TVM-VTM-3GB: The TVM-VTM-3GB input module for the TVM-40 and
TVM-9140 PKG (and TVM-9140 PKG-E) accepts two active-looping triple-rate
(2.97 Gb/s, 1.485 Gb/s, and 270 Mb/s) 3Gb/s-SDI, HD-SDI, or SD-SDI input
signals for display and analysis. It also supplies additional support for dual-link
HD-SDI 12-bit YC
B
C
R
and RGB video formats. One triple-rate SDI monitor output
follows the selected SDI video input, or an internal Test Signal Generator can be
To Next Page
Loading...