EasyManua.ls Logo

VMI VVS OL82 - Page 7

Default Icon
178 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
7 VVSU Operation ................................................................................... 7-1
7.1 General ................................................................................... 7-3
7.2 Start VVSU ............................................................................. 7-4
7.3 Screen layout (generic) .......................................................... 7-5
7.3.1 Main screen layout .................................................. 7-5
7.3.2 Menu bar ................................................................. 7-5
7.3.3 Interface Status ....................................................... 7-9
7.3.4 Screen Selection ..................................................... 7-10
7.3.4.1 Status screen ..................................................... 7-11
7.3.4.2 Calibration screen (for advanced users only) .... 7-13
7.3.4.3 System screen (for advanced users only) .......... 7-15
7.3.4.4 Material screen (for advanced users only) ......... 7-16
7.3.4.5 Actuator screen (only for advanced users) ........ 7-17
7.3.4.6 Display sensor screen ........................................ 7-18
7.3.4.7 Material scan screen .......................................... 7-19
7.3.4.8 Sensor screen (for advanced users only) .......... 7-22
7.3.4.9 History scan data screen ................................... 7-23
8 Troubleshooting .................................................................................. 8-1
8.1 Communication ...................................................................... 8-3
8.1.1 VVSU is not able to detect the VVSX server .......... 8-3
8.1.1.1 Setting the priority of the network card .............. 8-4
8.1.2 VVSU shows an error while attempting to connect
to the VVSX server ..................................................
8-4
8.2 Device detection at startup ..................................................... 8-11
8.2.1 Actuator version retrieval error ................................ 8-11
8.2.2 Camera Version retrieval error ................................ 8-12
8.2.3 Encoder detection error ........................................... 8-12
8.3 CAN-bus problems ................................................................. 8-14
8.3.1 Too many CAN timeout messages shown in the
VVSX window ..........................................................
8-14
8.4 Breaker centering problems ................................................... 8-16
8.4.1 Breaker centering switches too late to TE center
mode .......................................................................
8-16
8.4.2 Breaker centering switches too early to body
center mode ............................................................
8-17
8.4.3 Only half of the breaker is seen in the material
scan .........................................................................
8-18
8.4.4 Sometimes side guiding is applied when splice
guiding is selected ...................................................
8-19
8.4.5 Interfering ambient light ........................................... 8-19
8.5 Guiding problems ................................................................... 8-20
8.5.1 VVS is not guiding the Breaker material ................. 8-20
8.5.2 Splice guiding is not working ................................... 8-22
8.5.3 Homing problem (RK4004) ..................................... 8-23
8.5.4 Actuator RK4004 is not guiding breaker material ... 8-23
8.5.5 Correction overshoot ............................................... 8-24
8.5.6 Camera samples are delayed due to overexposure
of the camera ..........................................................
8-24
8.6 Calculation problems .............................................................. 8-26
8.6.1 VVS LE set point is calculated on the wrong side of
the material .............................................................
8-26
8.6.2 Holes in the body-ply are detected by the camera .. 8-27
8.6.3 Deviation between measured and actual bodyply
width (only for 24x) ..................................................
8-28
CONTENTS
THINKING FORWARD
VMI Vision System VVS (OL82) VVSX 13.0.12.0, VVSU 3.0.6 / 4 / 2016-07-11 / pd#175592
v

Table of Contents