Xerox WorkCentre 5021 - Page 288

08/2012
6-19
WorkCentre 5021/5019
6.1.24
General Procedures
Initial Issue
6.1.24 Alignment Specification
• Alignment Measurement Method and Specification (Calculated for 100%)
• Alignment (Calculated for 100% ) (Upper IOT Side 1, Lower IOT Side 2)
• (-) means a deviation in the Lead direction while (+) means a deviation in the Tail direc-
tion.
NOTE: . Effect of paper elongation and shrinkage due to environmental changes is not
included.
*1: Specified in the state where the center of the document is set correctly.
*2: Specified in the state where the Side Guide is set correctly.
*3: The User Adjustment Pitch is 0.254 mm.
*4: The User Adjustment Pitch is 0.135 mm.
Table 1
Item
SYSTEM Spec *1 (Platen)
SYSTEM Spec
(DADF)
IOT
IIT DADF ConditionsTray MSI *2 Tray MSI*2 STM
Lead Regi *3 +/- 2.8 mm
+/- 3.8 mm
+/- 3.6 mm
-
+/- 3.8 mm
+/- 4.4 mm
+/- 2.4 mm
+/- 3.4 mm
+/- 3.1 mm
-
+/- 3.1 mm
-
+/- 0.7 mm
-
+/- 1.5mm
+/- 1.5 mm
Side Regi *4 +/- 3.4 mm
+/- 3.8 mm
+/-3.6 mm
-
+/- 4.2 mm
+/- 4.6 mm
+/- 3.0 mm
+/- 3.4 mm
+/-3.2 mm
-
+/-3.1 mm
-
+/-0.75 mm
-
+/-1.5 mm
+/-1.5 mm
Lead Skew (200 mm) +/-2.4 mm
+/-2.8 mm
+/-2.7 mm
-
+/- 2.8 mm
+/- 3.2 mm
+/-1.9 mm
+/-2.3 mm
+/-2.2 mm
-
+/-1.9 mm
-
+/-0.8 mm
-
+/-1.0 mm
+/-1.0 mm
Side Skew (400 mm) +/-4.4 mm
+/-4.6 mm
+/-4.8 mm
-
+/- 5.4 mm
+/- 5.6 mm
+/-3.8 mm
+/-4.0 mm
+/-4.4 mm
-
+/-3.8 mm
-
+/-1.2 mm
-
+/-2.2 mm
+/-2.2 mm
Horizontal R/E Precision (All area)
Applicable for 100%
+/-1.05%
+/-1.4%
-
-
+/-1.6%
+/-2.0%
+/-0.95%
+/-1.3%
-
-
+/-0.31%
-
+/-0.5%
+/-0.5%
This value is for length of
280 mm
Vertical R/E Precision (All area)
Applicable for 100%
+/-1.05%
+/-1.4%
- +/-1.6%
+/-2.0%
+/-0.95%
+/-1.3%
-
-
+/-0.31% +/-0.5%
+/-0.5%
This value is for length of
400 mm
Perpendicularity (400 mm) +/-3.1 mm - +/-3.4 mm +/-1.7 mm - +/-1.7 mm +/-2.2 mm
+/-2.2 mm
Linearity (Vertical) 1.8 mm - 2.4 mm 1.4 mm -
-
0.8 mm
-
0.5 mm
0.5 mm
This value is for length of
400 mm
Linearity (Horizontal) 1.8 mm - 2.4 mm 1.4 mm - Not defined - This value is for length of
280 mm
Linearity (Diagonal) 1.8 mm -
-
2.4 mm 1.4 mm -
-
Not defined -
-
This value is for length of
283 mm
Parallelism (400 mm) +/-2.1 mm - +/-3.0 mm +/-2.0 mm - +/-0.7 mm +/-1.8 mm