16-10
IM 765501-01E
Command Function Page
:ACTual? Queries the actual number of stored points. 16-29
:CALCulate
:MINimum? Queries the minimum value among the stored measured values. 16-29
:MAXimum? Queries the maximum value among the stored measured values. 16-29
:AVERage? Queries the average value among the stored measured values. 16-29
:SDEViation? Queries the standard deviation of the stored measured values. 16-30
:DATA
:NUMBer <Integer>|MINimum|MAXimum|UP|DOWN
Sets the store data number. 16-30
:NUMBer? [MINimum|MAXimum] Queries the store data number. 16-30
:TIME? Queries the time stamp of the stored data. 16-30
:SOURce? Queries the source value of the stored data. 16-30
[:SENSe]? Queries the measured value of the stored data. 16-30
:SETup? Queries the stored data setup mnemonic. 16-30
:MONLy 1|0|ON|OFF Sets the measurement-only state (ON or OFF). 16-30
:MONLy? Queries the measurement-only state (ON or OFF). 16-30
External Input/Output Commands (ROUTe Group)
:ROUTe
:BNCI
:SELect TRIGger|SWEep|CONTrol
Selects the BNC input (trigger input, sweep start input, or control input). 16-31
:SELect? Queries the BNC input selection (trigger input, sweep start input,
or control input). 16-31
:CONTrol ILOCk|OUTPut|ZERO Selects the BNC control input (interlock, output control, or zero control). 16-31
:CONTrol? Queries the BNC control input selection (interlock, output control,
or zero control). 16-31
:BNCO
:SELect TRIGger|SWEep|CONTrol
Selects the BNC output (trigger output, sweep synchronization output,
or control output). 16-31
:SELect? Queries the BNC output selection (trigger output, sweep synchronization output,
or control output). 16-31
:TRIGger ORIGin|SCHange|MBEGin|MEND|PEND
Sets the BNC trigger output generation timing (trigger, source change,
measurement begin, measurement end, or pulse end). 16-31
:TRIGger? Queries the BNC trigger output generation timing (trigger, source change,
measurement begin, measurement end, or pulse end). 16-31
:SWEep ORIGin|TURN|ALL Sets the BNC sweep synchronization output generation timing
(sweep start, 1 turn end, all sweep end). 16-31
:SWEep? Queries the BNC sweep synchronization output generation timing
(sweep start, 1 turn end, all sweep end). 16-31
:CONTrol ILOCk|OUTPut|ZERO|PROGram
Selects the control output (interlock, output control, zero control,
or programmable). 16-32
:CONTrol? Queries the control output selection (interlock, output control, zero control,
or programmable). 16-32
:DIO5 OUTPut|ZERO Sets the function (output control or zero control) of pin 5 (control input)
of the external input/output connector. 16-32
:DIO5? Queries the function (output control or zero control) of pin 5 (control input)
of the external input/output connector. 16-32
:DIO6 ORIGin|SCHange|MBEGin|MEND|PEND
Sets the function (trigger start point, source change, measurement begin,
measurement end, or pulse end) of pin 6 (trigger output) of the external
input/output connector. 16-32
16.2 Commands
To Next Page
Loading...
Need help?
General
