Index-2
IM 04P01B01-01E
E
edge................................................................................... 1-31
effects of operating conditions ......................................... 12-22
EMC standards .......................................................................iii
end printout.............................................................. 1-22, 6-16
end printout 2..................................................................... 6-16
energized ................................................................... 1-11, 7-3
English, setting the language ............................................ 7-22
entering basic setting mode................................................. 4-2
entering characters .............................................................. 4-4
entering setting mode .......................................................... 4-2
entering values .................................................................... 4-3
error messages.................................................................. 10-1
ESC key............................................................................... 4-3
exponent ............................................................................ 1-26
external reference compensation ........................................ 1-5
F
FAIL/chart end output relay ............................................... 2-10
FAIL output ........................................................................ 1-29
fastest recording interval ................................................... 1-28
feeding the chart paper........................................................ 3-6
felt pen ................................................................................. 3-7
filter .................................................................... 1-5, 6-3, 7-20
format of the date .............................................................. 1-19
four arithmetic operation ............................................ 1-26, 9-5
front cover tab of the chart cassette .................................. 3-11
FUNC key operation ............................................................ 4-5
H
half life of the brightness.................................................. 11-10
handling precautions ........................................................... 2-1
header printout .................................................................. 1-22
heat sink .............................................................................. 3-3
high limit alarm .................................................................... 1-7
high limit on rate-of-change alarm ....................................... 1-7
hold ............................................................................ 1-9, 1-12
hold operation ...................................................................... 7-3
hysteresis ............................................................................ 1-8
I
initializing the recorder settings ......................................... 7-27
input computation .............................................................. 12-2
input range........................................................................... 5-1
input type ........................................................................... 12-1
inserting a character ............................................................ 9-3
inserting characters ............................................................. 4-4
installation location .............................................................. 2-2
instantaneous mode ........................................................App-1
integration time of the A/D converter ........................... 1-6, 7-4
internal clock adjustment ................................................... 1-30
internal light LED assembly ............................................... 11-3
interval (periodic printout) ................................................App-6
interval (rate-of-change alarm) .................................... 1-7, 7-3
isolation ........................................................................... 12-19
K
key lock.................................................................... 3-19, 7-18
keys ..................................................................................... 3-2
keys to be key-locked ........................................................ 7-18
L
language ............................................................................ 7-22
level ................................................................................... 1-31
linear scaling........................................................................ 5-3
List ..................................................................................... 3-14
loading the chart paper ........................................................ 3-4
logical computation .................................................... 1-26, 9-6
lot number.......................................................................... 1-22
lot number, setting of ......................................................... 6-16
low-cut ......................................................................... 5-6, 5-8
low limit alarm ...................................................................... 1-7
low limit on rate-of-change alarm ........................................ 1-7
M
main display....................................................................... 1-24
manual printout ........................................................ 1-19, 3-13
measurable range................................................................ 1-2
measuring input terminal ..................................................... 2-5
memory backup ............................................................... 12-22
menu (basic setting mode) .................................................. 4-8
menu, customization of...................................................... 1-32
menu (data display setup) ................................................... 8-2
menu (setting mode)............................................................ 4-7
message .............................................................................. 6-9
message format ................................................................. 6-20
message printout ............................................................... 1-19
message printout including measured value ..................... 1-23
message printout including measured value in ................. 6-20
model ...................................................................................... vi
mounting brackets ............................................................... 2-3
mounting hole ...................................................................... 3-1
moving average ......................................................... 1-5, 7-19
N
names of parts ..................................................................... 3-1
new chart speed printout ................................................... 1-19
non-hold..................................................................... 1-9, 1-12
non-hold operation............................................................... 7-3
normal operating conditions ............................................ 12-18
number of samples of moving average ............................... 6-4
O
offset compensation mark ...............................................App-1
ON/OFF input ...................................................................... 5-5
opening the display.................................................................ix
operation menus using the FUNC key................................. 4-5
operation mode.................................................................... 4-1
operations on the panel keys............................................... 4-2
optional accessories ............................................................. viii
optional functions............................................................. 12-13
optional terminal .................................................................. 2-8
order of precedence of computation .................................... 9-4
over value .......................................................................... 9-29
over values during periodic printout.................................App-5
P
packing materials....................................................................ix
panel .................................................................................... 2-3
panel cut dimensions ....................................................... 12-23
parallel connection............................................................... 2-5
partial expanded recording .................... 1-15, 6-6, 7-21, 9-16
password for releasing the key lock .................................. 7-18
password (key lock) ........................................................... 3-19
pen caps .............................................................................. 3-7
pen holder............................................................................ 3-7
Index
To Next Page
Loading...
Need help?
General
