Agilent Technologies 8712ET

Index-2 Programmer’s Guide
Index
calculating length, 6-20
block length
definite
, 4-4
indefinite
, 4-5
block parameters
, 9-13
blocks
definite and indefinite length
,
4-4, 4-5, 9-13
definite length
, 9-13
boolean parameters
, 9-12
brackets
, 11-4
use of in this manual
, 1-2, 9-
14
, 11-4
branching
, 9-5
brightness
monitor
, 11-22
buffer
graphics
, 7-6
buffering user graphics
, 11-24
bus
data
, 1-4
bus management commands
, 1-6
BUSY
, 11-18
byte order
, 6-7, 11-27
reversed
, 4-7
byte swapping
, 4-7
bytes per point, during data
transfer
, 6-8
C
c programming language
, 6-5, 6-
7
C_DIRECTivity
, 11-16
C_ISOLATION
, 11-16
C_LDMATCH
, 11-16
C_RTRACKING
, 11-16
C_SRCMATCH
, 11-16
C_TTRACKING
, 11-16
C1
, 1-8
C12
, 1-8
C2
, 1-8
C3
, 1-8
C4, 1-8
C8
, 1-8
CABLe
, 11-13
cable fault location
center distance
, 11-47
CENTer or LOWPass mode
,
11-48
frequency span selection
, 11-
48
start distance
, 11-47
stop distance
, 11-47
cable impedance
, 11-52
cable length
measuring
, 11-46
specifying
, 11-45
units
, 11-47
cable loss
, 11-45
cable scan
starting
, 11-52
cables
, 1-2
cal check
, 11-16
CAL hardkey (ES)
, 10-16
CAL hardkey (ET)
,10-19,10-20,
10-21
CALC:MARK
, 6-13
CALC1:DATA?
, 6-12
CALCulate
, 9-4, 11-5–11-11
CALibration
, 9-4, 11-12
calibration
correction factors
, 6-16
finding current type
, 11-44
full band
, 11-44
instrument state
, 11-43
measuring a load
, 11-44
measuring a short
, 11-43
measuring a standard
reflection
, 11-44
transmission
, 11-44
measuring a thru
, 11-44
measuring an open
, 11-43
restoring factory defaults
, 11-
44
saving
, 11-44
selecting the number of ports
,
11-44
standard
, 11-42
calibration annotation
, 11-38
calibration choice
querying
, 11-41
setting
, 11-41
calibration kit
port selection
, 11-42
selecting
, 11-42
calibration standard
selecting
, 11-42
cannot create program
, 13-13
capacitance
compensating
, 11-38
case-sensitivity
, 9-8
CATalog
, 11-35, 11-36
Cent_acknowledge
, 11-19
Cent_busy
, 11-19
Cent_on_line
, 11-19
Cent_out_of_paper
, 11-19
Cent_printer_err
, 11-19
CENTer
cable fault location mode
, 11-
48
center distance
cable fault location
, 11-47
center frequency
, 11-47
Centronics port
, 11-18
CH[1|2]AFWD
, 6-22
CH1AFWD
, 6-22
CH1BFWD
, 6-22
CH1RFWD
, 6-22
CH1SCORR1
, 6-23
CH1SCORR2
, 6-23
CH1SCORR3
, 6-23
CH1SCORR4
, 6-23
CH2AFWD
, 6-22
CH2BFWD
, 6-22
CH2RFWD
, 6-22
CH2SCORR1
, 6-23
CH2SCORR2
, 6-23
CH2SCORR3
, 6-23