Barco DP2K-12C

Index
engine fan - voltage low 52
engine fan - voltage too low 52
engine s witch - not ok 37
fcb - force lps/lamp off (overtemperature, lamp house not
connected or engine no t connected) 47
icp fan - speed low 72
icp fan - voltage high 73
icp fan - voltage low 73
imb - logical m arriage tamper event 69
imb - no comm unication 68
imb - physical marriage tamper eve nt 69
imb - s ervice door tamper event 69
lamp - lam p is off due to an error 6 0
lamp - no comm unication 29
lamp - set lam p on failed 60
lamp - temperature high 46
lamp - tem perature sensor open 46
lamp - tem perature sensor short 47
lamp - temperature too high 46
lamp anode fan - s peed low 34
lamp anode fan - speed too low 33
lamp anode fan - voltag e high 53
lamp anode fan - voltage low 53
lamp anode fan - voltage too low 53
lamp ca thode fan - speed low 35
lamp cathode fan - speed too low 34
lamp cathode fan - voltage high 54
lamp cathode fan - voltage low 54
lamp cathode fan - voltage too low 54
lamp hous e - not connected 37
lamp power supplies - at least one lamp power supply could not
be detected 59
lamp power supplies - communication failed 31
lamp power supplies - communication f ailed with at least one
lamp power supply 59
lamp power supplies - lamp is on, but s mps is off 59
lamp po wer supplies - zero lam p power supplies detected 58
lamp r ear fan - speed low 36
lamp re ar fan - v oltage high 55
lamp re ar fan - voltage low 56
lamp rear fan - volta ge too low 55
lamp run time - exceeds maximu m 60
lamp r un time - read failed 60
lamp run time - read limits failed 60
lamp r un time - warning 60
lens - no lens parameter file has been activated 73
lens focus position - requested target not reached 39
lens horizontal shift position - requested target not reached 40
lens mo tors - voltage too low 72
lens vertical s hift position - requested target not reached 41
lens zoom position - requested target not reached 38
light pipe - temp erature high 69
light p ipe - tem perature sensor open 70
light p ipe - tem perature sensor short 70
light pipe - tem perature too high 69
light sensor - no communication 29
maintenance - m aintenance required 73
pfc heatsink - temperature high 48
prism sw itch - warning (lens probably touches prism) 38
smps fan - voltage high 55
smps fan - voltage low 55
smps fan - voltage too low 55
smps fan 1 (left side) - speed low 35
smps fan 2(right side) - speed low 36
smps primary heatsink - temperature high 49
smps secondary heatsink - tem perature high 49
smps s econdary heatsink - temperature sen sor open 49
smps s econdary heatsink - temperature sen sor short 49
system - read projector identification failed 32
ti-boards - system status = fail 61
ti-icp - certificate error 65
ti-icp - icp board not detected 66
ti-icp - key error 66
ti-icp - read satellite info failed 63
ti-icp - read system status failed 63
ti-icp - satellite firmwa re mismatch 63
ti-icp - s elf test = fail 65
ti-link-decryptor - logical marriage tamper event 68
ti-link-decryptor - no communication 66
ti-link-decryptor - phys ical mar riage tamper event 68
ti-link-decryptor - read system status failed 68
ti-link-decryptor - security log almost full 68
ti-link-decryptor - security log is full 68
ti-link-decryptor - security tamper event 67
ti-link-decryptor - s ervice door tamper event 62
ti-link-decryptor - sy stem error 66
Error code number 29, 31–63, 65–73
5003 29
5004 29
5005 31
5020 32
5042 32
5053 33
5072 33
5073 34
5082 34
5083 35
5103 35
5113 36
5123 36
5143 36
5160 37
5180 37
5191 38
5230 38
5231 39
5232 40
5233 41
5253 41
5263 42
5273 43
5280 43
5281 43
5283 43
5284 43
5285 43
5290 44
5291 44
5293 44
5294 44
5295 45
5300 45
5301 45
5303 45
5304 45
5305 46
5310 46
5311 46
5314 46
5315 47
5320 47
5331 48
5340 48
5341 48
5343 48
5344 48
5345 49
5351 49
5361 49
5364 49
5365 49
5371 49
5372 49
5373 50
5381 50
5382 50
5383 50
5391 50
5392 50
5393 51
5431 51
5432 51
352
R5905043 DP2K-12C/11CX 19/02/2018