1 689 989 087 2018-07-24| Robert Bosch GmbH
| CRI/CRIN 848H | 51
en
en – Contents
1. Symbols used 53
1.1 In the documentation 53
1.1.1 Warning notices -
Structure and meaning 53
1.1.2 Symbols in this documentation 53
1.2 On the product 53
2. User information 53
2.1 Important notes 53
2.2 Safety instructions 53
2.3 Electromagnetic compatibility (EMC) 53
2.4 General information 54
2.5 Definition of terms 54
3. Product description 54
3.1 Intended use 54
3.2 Prerequisites 54
3.2.1 Prerequisites 54
3.2.2 Training 55
3.3 User group 55
3.4 Delivery specification 55
3.5 General overview 56
3.6 Tester set components 58
3.6.1 Clamping device 58
3.6.2 Injector holder 59
3.6.3 Holding device 1 685 200 149 59
3.6.4 Retaining plate 60
3.6.5 Connection adapter 60
3.6.6 High pressure pump 60
3.6.7 Control electronics 61
3.6.8 Adapter lead 61
3.6.9 High-pressure hose (special accessory) 62
3.6.10 High-pressure hose 1 680 712 325 63
3.6.11 Hose line for return quantity 63
3.6.12 Hose line for injection quantity 63
3.6.13 Return hose 1 680 712 371 64
3.6.14 Return adapter for passenger vehicle
injectors 64
3.6.15 Return adapter for commercial vehicle
injectors with hose connection 64
3.6.16 Return adapter for commercial vehicle
injectors with threaded connection 64
3.6.17 Test pressure line 65
4. Initial startup 66
4.1 Clamping high-pressure pump 66
4.1.1 EPS 708 66
4.1.2 EPS 815 66
3.7 Special accessories 66
4.2 Hydraulic connection of high-pressure pump 67
4.3 Fitting frame 68
4.3.1 EPS 708 68
4.3.2 EPS 815 69
4.4 Hydraulic connection of clamping device 69
4.5 Fitting trigger electronics 70
4.6 Electrical connection of clamping device 71
4.6.1 EPS 708 71
4.6.2 EPS 815 71
4.7 Fitting injector holder 72
4.8 Hose 1 680 712 310 72
5. Preparing for testing 73
5.1 Cleaning instructions for injectors 73
5.2 Passenger vehicle injectors 73
5.2.1 Preparing the injection chamber 73
5.2.2 Clamping injector 74
5.2.3 Connecting the test pressure line 75
5.2.4 Connecting return adapter 76
5.2.5 Connecting hose line for return quantity
and injection quantity 76
5.2.6 Connecting injectors electrically 77
5.3 Commercial vehicle injectors with external
connections 78
5.3.1 Preparing the injection chamber 78
5.3.2 Clamping injector 79
5.3.3 Connecting high pressure hose 81
5.3.4 Attach return adapter 82
5.3.5 Connecting hose line for return quantity
and injection quantity 82
5.3.6 Connect injectors electrically 83
5.4 Commercial vehicle injectors with internal
connections 84
5.4.1 Fitting connection adapter 84
5.4.2 Preparing the injection chamber 85
5.4.3 Clamping injector 86
5.4.4 Connecting high pressure hose 87
5.4.5 Connecting hose line for return quantity
and injection quantity 89
5.4.6 Connect injectors electrically 90
To Next Page
Loading...
