BST CLS Pro 600 - E Appendix 5 - Teach-in Template

108 pages

Save Page as PDF

To Next Page

To Previous Page

Appendix 5 - Teach-in Template

CLS Pro 600 – Line and Contrast Sensor 107/108

E Appendix 5 - Teach-in Template

Main Page

Table of Contents3
About this Document6
What You Need to Know6
Target Group6
Storage and Distribution6
Meanings of the Safety Instructions and Symbols6
Safety Instructions6
Symbols7
Operation Using Keys7
More Detailed Information7
Description8
General Information8
Intended Use8
System Description9
System Design9
Functional Principle10
Terms Used in this Manual12
General Information12
Set Position13
Measuring Range14
Search Area14
Status Bar15
Footer15
First Edge / Second Edge15
Control Panel16
Graphic Display16
Safety Information17
Laser19
Emissions19
Assembly20
Installation Site Requirements20
Sensor Installation20
General Information20
Sensor with Supplied Holder20
Installing the Sensor Using a Holder Supplied by the Customer21
Setting the Gap between the Sensor and the Sensing Roller22
Turning the Control Panel22
Rotating the Control Panel24
Installing the Control Panel25
General Information25
Dismantling the Holder25
Wall Mounting27
Console Installation31
Installation35
Fitting the Cable Connections35
Sensor35
Enclosure Sockets35
Service Indicator Displays36
Bus Status Leds36
Unit Status LED37
Setting the DIL Switches37
Commissioning38
Menus39
General Information39
Input Options39
Main Menu39
Commissioning with a Controller43
Ekrpro Com6043
Ekr 500 Plus / Ekr 500 Digital44
EKR 1500 / CCD Line Guider and C2M Coupler44
Operation45
General Information45
Operating Display45
Setup Mode Display Window45
Scanning Mode Display Window47
Status Bar48
Remote Control of Ekrpro Com60 / Ekr 500 Plus / Ekr 500 Digital Controllers48
Manual Mode49
Automatic49
Servo Center Position49
Moving the Set Point Position (W-Value)50
Moving the Guiding Device50
Setting the Controller Gain50
Operation51
General Information51
Activating Line Setup / Edge Setup51
Standard Operation51
Selecting a Job51
Edge Setup Mode52
Line Setup Mode54
Extended Operation56
Change User56
Job Administration57
Assigning User Levels to the Parameters58
Setting up Quick Menus59
Setup Administration60
Main Menu Parameter Meanings61
Configuration61
Parameter62
Remote Control EKR65
Display76
System Info77
Factory Default Settings78
Device Addresses78
Sensor Device Address78
Control Panel Device Address79
Terminator Resistors80
Sensor Terminator Resistors80
Control Panel Terminator Resistor81
Restoring Factory Default Settings82
Troubleshooting / FAQ83
Technical Data84
Sensor84
Environmental Conditions84
Power Supply84
Digital Inputs84
Digital Outputs84
Analogue Output84
Measuring Window Cover85
Control Panel Interface85
Weight / Dimensions85
Control Panel85
Environmental Conditions85
Power Supply85
Display85
Space Requirement (Details in MM)86
Plug Assignment88
Maintenance90
10.1 General Information90
10.2 Sensor90
10.3 Control Panel90
Transport / Storage91
11.1 Transport91
11.2 Storage91
Decommissioning92
Index93
A Appendix 1 - Commissioning as a Stand-Alone System95
A1 Blockage95
A2 Control Signal95
A3 Commissioning95
A4 Configuring the Guiding Block Output96
A5 Defining the Mounting Position97
B Appendix 2 - Saving Parameters and Loading Firmware98
B1 Save Parameters98
B2 Loading Firmware98
B2.1 Loading Sensor Firmware99
B2.2 Loading Panel Firmware99
C Appendix 3 - Factory Default Settings100
D Appendix 4 - BST Eltromat STB 1 Connections104
D1 Installation Instructions for EMC-Wiring105
E Appendix 5 - Teach-In Template107
E1 Aligning the Teach-In Template in Front of the CLS Pro 600108

Other manuals for BST CLS Pro 600

Quick Reference Guide21 pages

Related product manuals

BST CCD CAM 100

198 pages

BST CLS Pro 600 - E Appendix 5 - Teach-in Template

Table of Contents

Other manuals for BST CLS Pro 600

Related product manuals