Check Point UTM-1 Edge

To Next Page

To Previous Page

Using the UTM-1 Portal

Chapter 4: Getting Started 93

Element Description

Status bar Shows your Internet connection and managed services status.

Figure 19: UTM-1 Portal

Main Page

Table of Contents7
About this Guide13
Introduction15
About Your Check Point UTM-1 Embedded NGX Appliance15
The UTM-1 Edge X Series and UTM-1 Edge W Series16
Contacting Technical Support52
UTM-1 Security53
Introduction to Information Security53
The UTM-1 Firewall58
Installing and Setting up UTM-167
Before You Install the UTM-1 Appliance67
UTM-1 Edge X and UTM-1 Edge W Installation81
Cascading Your Appliance96
Connecting the Appliance to Network Printers97
Setting up the UTM-1 Appliance97
Getting Started101
Initial Login to the UTM-1 Portal101
Appliance102
Logging on to the UTM-1 Portal103
Accessing the UTM-1 Portal Remotely Using HTTPS105
Using the UTM-1 Portal106
Logging off110
Configuring the Internet Connection111
Overview111
Using the Internet Wizard112
Using Internet Setup127
Setting up Dialup Modems159
Viewing Internet Connection Information166
Enabling/Disabling the Internet Connection168
Using Quick Internet Connection/Disconnection169
Configuring a Backup Internet Connection169
Configuring WAN Load Balancing170
Managing Your Network173
Configuring Network Settings173
Using Network Objects202
Configuring Network Service Objects213
Using Static Routes216
Managing Ports223
Using Bridges235
Overview235
Workflow241
Adding and Editing Bridges242
Adding Internal Networks to Bridges246
Adding Internet Connections to Bridges251
Deleting Bridges256
Configuring High Availability257
Overview257
Configuring High Availability on a Gateway260
Sample Implementation on Two Gateways264
Using Traffic Shaper269
Overview269
Setting up Traffic Shaper270
Predefined Qos Classes271
Adding and Editing Classes273
Viewing and Deleting Classes277
Restoring Traffic Shaper Defaults278
Working with Wireless Networks279
Overview279
Configuring Wireless Networks287
Troubleshooting Wireless Connectivity316
Viewing Reports319
Viewing the Event Log319
Using the Traffic Monitor322
Viewing Computers326
Viewing Connections328
Viewing Wireless Statistics330
Viewing ADSL Statistics334
Viewing the Routing Table336
Setting Your Security Policy339
The UTM-1 Firewall Security Policy340
Default Security Policy341
Setting the Firewall Security Level342
Configuring Servers345
Using Rules348
Using Port-Based Security361
Using Secure Hotspot365
Using NAT Rules371
Using Web Rules379
Using Smartdefense389
Overview389
Configuring Smartdefense390
Smartdefense Categories397
Resetting Smartdefense to Its Defaults438
Using Vstream Antivirus439
Overview439
Enabling/Disabling Vstream Antivirus442
Viewing Vstream Antivirus Signature Database Information443
Configuring Vstream Antivirus444
Updating Vstream Antivirus458
SMART Management and Subscription Services459
Connecting to a Service Center460
Viewing Services Information465
Refreshing Your Service Center Connection466
Configuring Your Account467
Disconnecting from Your Service Center467
Web Filtering468
Email Filtering475
Automatic and Manual Updates480
Working with Vpns483
Overview484
Setting up Your UTM-1 Appliance as a VPN Server490
Adding and Editing VPN Sites503
Viewing and Deleting VPN Sites537
Enabling/Disabling a VPN Site537
Logging on to a Remote Access VPN Site538
Logging off a Remote Access VPN Site541
Installing a Certificate542
Uninstalling a Certificate550
Viewing VPN Tunnels551
Viewing IKE Traces for VPN Connections554
Viewing VPN Topology555
Managing Users557
Changing Your Login Credentials557
Adding and Editing Users560
Adding Quick Guest Hotspot Users564
Viewing and Deleting Users566
Setting up Remote VPN Access for Users567
Using RADIUS Authentication567
Configuring RADIUS Attributes574
Using Remote Desktop579
Overview579
Workflow580
Configuring Remote Desktop581
Configuring the Host Computer584
Accessing a Remote Computer's Desktop587
Maintenance591
Viewing Firmware Status592
Updating the Firmware594
Upgrading Your License596
Configuring Syslog Logging598
Controlling the Appliance Via the Command Line600
Configuring HTTPS606
Configuring SSH609
Configuring SNMP611
Setting the Time on the Appliance616
Using Diagnostic Tools620
Backing up the UTM-1 Appliance Configuration634
Resetting the UTM-1 Appliance to Defaults637
Running Diagnostics640
Rebooting the UTM-1 Appliance641
Using Network Printers643
Overview643
Setting up Network Printers644
Configuring Computers to Use Network Printers646
Viewing Network Printers663
Changing Network Printer Ports664
Resetting Network Printers665
Troubleshooting667
Connectivity667
Service Center and Upgrades671
Other Problems672
Specifications673
Technical Specifications673
CE Declaration of Conformity681
Federal Communications Commission Radio Frequency Interference Statement688
Glossary of Terms691
Index697

Check Point UTM-1 Edge - Page 107

Table of Contents

Related product manuals