Cisco Telepresence MX800 Reference Guide

D15335.02 Cisco TelePresence MX700 and MX800 API Reference Guide CE8.0, FEBRUARY 2016.
Copyright © 2016 Cisco Systems, Inc. All rights reserved. 174
Cisco TelePresence MX700 and MX800
API Reference Guide
xStatus Video Output Connector [n] ConnectedDevice PreferredFormat
Shows the preferred input format of the monitor connected to the HDMI port as defined in the
monitors EDID. This is not necessarily the format the codec is sending out.
Value space of the result returned:
String
Example:
xStatus Video Output Connector 1 ConnectedDevice PreferredFormat
*s Video Output Connector 1 ConnectedDevice PreferredFormat: "1920x1080@60Hz"
** end
xStatus Video Output Connector [n] MonitorRole
Describes which video stream is shown on the device that is connected to the video output
connector.
First/Second/Third: The role of the monitor in a multimonitor setup. In a singlemonitor setup,
there is no difference between First, Second and Third.
PresentationOnly: Shows presentation video stream if active.
Recorder: Shows all participants, including the local main video. If active, shows also the
presentation.
Value space of the result returned:
First/Second/Third/PresentationOnly/Recorder
Example:
xStatus Video Output Connector 1 MonitorRole
*s Video Output Connector 1 MonitorRole: First
** end
xStatus Video Output Connector [n] Resolution Height
Shows the resolution height (in pixels) for the video output connector.
Value space of the result returned:
120..3000
Example:
xStatus Video Output Connector 1 Resolution Height
*s Video Output Connector 1 Resolution Height: 1080
** en
xStatus Video Output Connector [n] Resolution RefreshRate
Shows the resolution refresh rate (Hz) for the video output connector.
Value space of the result returned:
1..300
Example:
xStatus Video Output Connector 1 Resolution RefreshRate
*s Video Output Connector 1 Resolution RefreshRate: 60
** end
xStatus Video Output Connector [n] Resolution Width
Shows the resolution width (in pixels) for the video output connector.
Value space of the result returned:
176..4000
Example:
xStatus Video Output Connector 1 Resolution Width
*s Video Output Connector 1 Resolution Width: 1920
** end
xStatus Video Output Connector [n] Type
Shows the type of connector.
HDMI: It is an HDMI connector.
DVI: It is an DVI connector.
Value space of the result returned:
HDMI/DVI
Example:
xStatus Video Output Connector 1 Type
*s Video Output Connector 1 Type: HDMI
** end
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatus

xStatus

Cisco Telepresence MX800 Specifications

General

Pan range	-90 - 60 °
Product type	Video conferencing service management system
Product color	White
Wall mountable	Yes
Tilt angle range	-14 - 12 °
Number of persons	- person(s)
Aspect ratio	16:9
Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.263, H.264, H.265
Resolution at capture speed	1920x1080@60fps
Supported graphics resolutions	352 x 288, 512 x 288, 1024 x 576 (WSVGA), 1024 x 768 (XGA), 1280 x 720 (HD 720), 1280 x 768 (WXGA), 1920 x 1080 (HD 1080), 1920 x 1200 (WUXGA)
Megapixel	- MP
Sensor type	-
Digital zoom	2 x
Optical zoom	10 x
Image sensor size	- \
Closest focusing distance	1 m
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Display diagonal	70 \
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	591 W
Power consumption (typical)	571 W