Cisco TelePresence SX80 User Manual

D15107.0 5 Codec SX80 API Reference Guide TC7.3, OCTOBER 2015. Copyright © 2015 Cisco Systems, Inc. All rights reserved. 120
Cisco TelePresence SX80 API Reference Guide
xCommand Phonebook ContactMethod Add
Add contact details for an existing contact in the local phonebook. The command returns the
ContactMethodId, which is a unique string that identifies the contact method; typically the format is
“n”.
You can add several contact methods to a contact. Note that only the first contact method will
appear in the Favorites list on the Cisco TelePresence Touch controller. The first contact method
may have been created when issuing the xCommand Phonebook Contact Add command to make
the contact. All contact methods are available in the API and on the web interface.
ContactId: The unique identifier for the contact that you want to add a contact method to. The
identifier will be returned by an xCommand Phonebook Search command. It was also returned when
the xCommand Phonebook Contact Add command was issued to make the contact.
Device: Set which type of device to call to.
Number(r): The phone number or address of the contact.
Protocol: Select Auto, SIP, H323 or H320 protocol.
CallRate: Set a call rate.
CallType: Select a call type (audio or video).
Requires user role: USER
Parameters:
ContactId(r): <S: 0, 255>
Device: <Mobile/Other/Telephone/Video>
Number(r): <S: 0, 255>
Protocol: <Auto/H320/H323/SIP>
CallRate: <0..6000>
CallType: <Audio/Video>
Example:
xCommand Phonebook ContactMethod Add ContactId:localContactId-2
Number:54321 Protocol:H323
xCommand Phonebook ContactMethod Delete
Delete a contact method from an existing contact in the local phonebook.
ContactId: The unique identifier for the contact you want to change. The identifier will be returned
by an xCommand Phonebook Search command. It was also returned when the xCommand
Phonebook Contact Add command was issued to make the contact.
ContactMethodId: The unique identifier for the contact method you want to delete. The identifier
will be returned by an xCommand Phonebook Search command. It was also returned when the
xCommand Phonebook ContactMethod Add command was issued to make the contact method.
Requires user role: USER
Parameters:
ContactId(r): <S: 0, 255>
ContactMethodId(r): <S: 0, 255>
Example:
xCommand Phonebook ContactMethod Delete ContactId:localContactId-2
ContactMethodId:1
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatus
xCommand

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g