Cisco TelePresence SX80 User Manual

D15107.0 5 Codec SX80 API Reference Guide TC7.3, OCTOBER 2015. Copyright © 2015 Cisco Systems, Inc. All rights reserved. 121
Cisco TelePresence SX80 API Reference Guide
xCommand Phonebook ContactMethod Modify
Modify details about the contact method for an existing contact in the local phonebook.
ContactId: The unique identifier for the contact. The identifier will be returned by an xCommand
Phonebook Search command. It was also returned when the xCommand Phonebook Contact Add
command was issued to make the contact.
ContactMethodId: The unique identifier for the contact method you want to modify. The identifier
will be returned by an xCommand Phonebook Search command. It was also returned when the
xCommand Phonebook ContactMethod Add or xCommand Phonebook Contact Add commands
were issued to make the contact method.
Device: Set which type of device to call to.
Number: The phone number or address of the contact.
Protocol: Select Auto, SIP, H323 or H320 protocol.
CallRate: Set a call rate.
CallType: Select a call type (audio or video).
Requires user role: USER
Parameters:
ContactId(r): <S: 0, 255>
ContactMethodId(r): <S: 0, 255>
Device: <Mobile/Other/Telephone/Video>
Number: <S: 0, 255>
Protocol: <Auto, H320/H323/SIP>
CallRate: <0..6000>
CallType: <Audio/Video>
Example:
xCommand Phonebook ContactMethod Modify ContactMethodId:117
ContactId:localContactId-10 Number:"newnumber@cisco.com"
xCommand Phonebook Folder Add
Phonebook entries can be stored in folders. Use this command to add a folder to the local phone-
book. The command returns the FolderId, which is a unique string that identifies the folder; typically
the format is “localGroupId-n”.
Name(r): The name of the folder.
ParentFolderId: The unique identifier for the parent folder. The identifier will be returned by an
xCommand Phonebook Search command. It was also returned when the xCommand Phonebook
Folder Add command was issued to make the parent folder.
Requires user role: USER
Parameters:
Name(r): <S: 0, 255>
ParentFolderId: <S: 0, 255>
Example:
xCommand Phonebook Folder Add Name: "New York Office"
xCommand Phonebook Folder Delete
Delete an existing folder from the local phonebook.
FolderId: The unique identifier for the folder. The identifier will be returned by an xCommand
Phonebook Search command. It was also returned when the xCommand Phonebook Folder Add
command was issued to make the folder.
Requires user role: USER
Parameters:
FolderId(r): <S: 0, 255>
Example:
xCommand Phonebook Folder Delete FolderId:localGroupId-3
Contents
Introduction
About the API
xConfiguration
Appendices
xCommand
xStatus
xCommand

Cisco TelePresence SX80 Specifications

General

Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.262, H.263, H.264, H.265
Supported graphics resolutions	1280 x 720 (HD 720), 1920 x 1080 (HD 1080)
Voice codecs	G.711, G.722, G.722.1, G.729ab
Noise reduction	Yes
HDMI ports quantity	5
DVI-D ports quantity	1
USB 2.0 ports quantity	2
Product color	Silver
Rack capacity	1U
Number of persons	0 person(s)
Analog signal format system	NTSC, PAL
Security algorithms	HTTPS, SSH
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Supported network protocols	SIP, H.323, ISDN, TCP/IP, DHCP, QoS
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Sensor type	-
Image sensor size	- \

Weight and Dimensions

Depth	309.8 mm
Width	442 mm
Height	44 mm
Weight	3650 g