90
6-4. Setting the Channel Level for Zone2
• Use this setting to adjust so that the playback level between the different channels of Zone2 is equal.
• From the Zone2 listening position, listen to the test tones produced from the speakers used in Zone2 to adjust the level.
• The level can also be adjusted directly from the Remote control unit. (For details, see pages 159, 160.)
¥¥¥
¥¥Ĺ©ŔūŠŜŦŠŭ¥ńŪũšŤŢ©
¥¥ĺ©ŔŰŝŲŪŪšŠŭ¥ŎŪşŠ
¥¥Ļ©ŅŠŧŜŴ¥ŕŤŨŠ
¥¥ļ©ńţŜũũŠŧ¥ōŠűŠŧ
¥¥Ľ©ńŭŪŮŮŪűŠŭ¥ŇŭŠŬŰŠũŞŴ
¥¥ľ©ŗŤşŠŪ¥ŔŠůŰū
¥¥Ŀ©śŪũŠĻÃļ¥ŕŪũŠÃńţ¥ōŠű©
¥¥ņųŤů
¥ľ©śŪũŠ¥ŔŠůŰū
¥ľáļ©ńţŜũũŠŧ¥ōŠűŠŧ
¥
¥¥ŕŠŮů¥ŕŪũŠ¥¥¥¥¥¥«¥¥
¥
¥¥ŕŠŮů¥ŕŪũŠ¥ŔůŜŭů
¥
¥¥ōŠűŠŧ¥ńŧŠŜŭ
¥
¥
¥
;G U
;G U
/CPWCN
#WVQ
<QPG
1
2
Select “Channel Level” at the Zone Setup Menu.
Display the Channel Level screen.
Z2 Channel Lev.
*Zone Setup
T.Tone: Auto
*Z2 Channel Lev
(Main unit) (Remote control unit)
(Main unit) (Remote control unit)
¥ľáļ©ńţŜũũŠŧ¥ōŠűŠŧ
¥
¥¥ŕŠŮů¥ŕŪũŠ¥¥¥¥¥¥«¥¥
¥
¥¥ŕŠŮů¥ŕŪũŠ¥ŔůŜŭů
¥
¥¥ōŠűŠŧ¥ńŧŠŜŭ
¥
¥
¥
;G U
;G U
/CPWCN
#WVQ
<QPG
3
Select the mode.
Select “Auto” or “Manual”.
Example: When the “Auto” mode is selected
T.Tone: Auto
*Z2 Channel Lev
Auto :
Adjust the level while listening to the test tones
produced automatically from each speaker.
Manual :
Select the speaker from which you want to
produce the test tone to adjust the level.
(Main unit) (Remote control unit)
4
5
Select “Test Tone Start”.
¥ľáļ©ńţŜũũŠŧ¥ōŠűŠŧ
¥
¥¥ŕŠŮů¥ŕŪũŠ¥¥¥¥¥¥«¥¥
¥
¥¥ŕŠŮů¥ŕŪũŠ¥ŔůŜŭů
¥
¥¥ōŠűŠŧ¥ńŧŠŜŭ
¥
¥
¥
;G U
;G U
/CPWCN
#WVQ
<QPG
Select “Yes”.
Tone Start:Yes
*Z2 Channel Lev
(Main unit) (Remote control unit)
(Main unit) (Remote control unit)
To Next Page
Loading...
Need help?
General
