93
6-6. Setting the Video Setup for Zone2
[1] Video Convert Mode (Zone2)
• Select the video input signal to be output to the Zone2 composit, S-Video and component monitor output terminals using the video
conversion function.
¥ľáľ©ŗŤşŠŪ¥ŔŠůŰū
¥
¥
¥¥¥¥ŗŤşŠŪ¥ńŪũűŠŭů¥ŎŪşŠ
¥
¥¥¥¥łŰşŤŪ¥ŅŠŧŜŴ
¥
¥
¥¥¥¥ņųŤů
¥
<QPG
Z2 Video Mode
*Z2 Video Setup
1
Select “Video Setup” at the Zone Setup Menu.
¥¥¥
¥¥Ĺ©ŔūŠŜŦŠŭ¥ńŪũšŤŢ©
¥¥ĺ©ŔŰŝŲŪŪšŠŭ¥ŎŪşŠ
¥¥Ļ©ŅŠŧŜŴ¥ŕŤŨŠ
¥¥ļ©ńţŜũũŠŧ¥ōŠűŠŧ
¥¥Ľ©ńŭŪŮŮŪűŠŭ¥ŇŭŠŬŰŠũŞŴ
¥¥ľ©ŗŤşŠŪ¥ŔŠůŰū
¥¥Ŀ©śŪũŠĻÃļ¥ŕŪũŠÃńţ¥ōŠű©
¥¥ņųŤů
¥ľ©śŪũŠ¥ŔŠůŰū
Z2 Video Setup
*Zone Setup
2
Display the Video Setup screen.
3
Select “Video Convert Mode”, then press the
ENTER button.
Display the Video Convert Mode.
(Main unit) (Remote control unit)
(Main unit) (Remote control unit)
(Main unit)
(Remote control unit)
(Main unit)
(Remote control unit)
ľáľ©ŗŤşŠŪ¥ńŪũűŠŭů¥ŎŪşŠ
¥¥¥¥¥¥«¥łŖŕŐ
¥¥¥¥¥¥«¥łŖŕŐ
¥¥¥¥¥¥«¥łŖŕŐ
¥¥¥¥¥¥«¥łŖŕŐ
¥¥¥¥¥¥«¥łŖŕŐ
¥¥¥¥¥¥«¥łŖŕŐ
¥¥¥¥¥¥«¥łŖŕŐ
¥¥¥¥¥¥«¥łŖŕŐ
¥¥¥¥¥¥«¥łŖŕŐ
<QPG
&8&
8#WZ
8&2
68
&$5
8%4
8%4
8%4
8%4
4
q Select the Zone2 input source. w Select the mode as below.
AUTO : When there are multiple input signals for the input sources selected at Zone2, the input signal is detected and the input
signal output to the Zone2’s monitor output terminal is selected automatically, in the following order of priority:
Component, S-Video, Composite.
Component : The component video input signal is always selected.
If there is no component input signal among the input sources selected at Zone2, no video signals are output to the Zone2
component monitor output terminal.
S-Video : The S-Video input signal is always selected.
Video : The composite input signal is always selected.
OFF : The convert function does not operate.
The video signal of the input source selected at Zone2 is only output to the Zone2 video monitor output terminal.
The S-Video signal selected at Zone2 is only output to the Zone2 S-Video monitor output terminal.
If “Yes” is selected for “Default”, the settings are automatically reset to the default values.
AUTO
Component
S-video Video OFF
The details in each mode are as follows.
(Main unit) (Remote control unit)
(Main unit) (Remote control unit)
To Next Page
Loading...
Need help?
General
