Dynapac F6C - Page 125

To Next Page

To Previous Page

F 29

F F6C.GB 29-30 0504

Fuse board (3)

Nr. F5.9 - F5.14 A

1. free

2. free

3. free

4. Main fuse for traction drive 15

5. Sensors / diagnosis for traction drive 1

6. Control fuse for traction drive 1

1 2

3 4 5 6

Fuse1.Tif

Main Page

Table of Contents5
A Correct Use and Application9
B Vehicle Description11
Application11
Description of Assemblies and Functions12
Vehicle13
Construction13
Safety Devices16
Emergency Stop Button16
Steering16
Horn16
Ignition Key / Lights16
Safety Devices on the Gas Heater System16
Master Switch18
Hopper Transport Safeguard18
Screed Transport Safeguard18
Latch for Protective Roof (1)19
Additional Safety Devices20
Miscellaneous Equipment20
Technical Data, Standard Configuration21
Dimensions21
Weights22
Performance Data23
Traction Drive/Chassis23
Engine23
Hydraulic System24
Material Compartment (Hopper)24
Material Conveying24
Material Distribution25
Screed Control System25
Electrical System26
Gas Heating System for the Screed (O)26
Location of Instruction Labels and Type Plates27
Identification Label for the Paver Finisher (4)29
Identification Label for the Liquefied Gas System (12)30
Standards31
Continuous Sound Pressure Level31
Operating Conditions During Measurement31
Measuring Point Configuration31
Vibration Acting on the Entire Body32
Vibrations Acting on Hands and Arms32
Electromagnetic Compatibility (EMC)32
C Transportation33
Safety Regulations for Transportation33
Transportation on Low-Bed Trailers34
Preparations34
Driving Onto the Low-Bed Trailer35
After Transportation35
Transportation on Public Roads36
Preparations36
Driving on Public Roads37
Loading by Crane38
Towing39
Safely Parking the Vehicle40
D Operation41
Safety Regulations41
Controls42
Operating Panel42
Remote Control60
Front60
Rear61
Operating Elements on the Paver Finisher62
Engine Speed Adjuster (67)62
Batteries (68)63
Battery Main Switch (69)63
Transport Safeguards for the Hopper (70)63
Conveyor Limit Switch (Paddle) (71)64
Ultrasonic Auger Limit Switch (72)65
Sockets for Working Lights (Left and Right) (73)65
Sockets for Automatic Levelling/Slope (74)66
Socket for Remote Control (75)66
Vibration (76) and Tamper (Screed-Specific) (77) Speed Control67
Emulsion Spray System (80), (81)68
Collapsible Roof Lock (LH and RH on the Rear Console) (82)68
Mechanical Screed Transport Safeguard (Left and Right) (90)69
Seat Lock (Behind the Driver's Seat) (91)70
Operation71
Preparing for Operation71
Required Devices and Aids71
Before Starting Work (in the Morning or When Starting Paving)71
Check List for the Machine Operator72
Starting the Paver Finisher73
Before Starting the Paver Finisher73
Normal" Starting73
External Starting (Starting Aid)74
After Starting75
Indicator Lamps76
Oil Pressure Indicator Lamp for the Diesel Engine (1)76
Battery Charge Indicator (2)76
Preparations for Paving77
Separating Agent77
Screed Heater System77
Direction Marks77
Loading/Distributing Material78
Driving off for Laying79
Checks During Paving81
Paver Function81
Quality of the Layer81
Paving with Screed Stop82
General82
Deactivation of Floating Position82
Interrupting/Terminating Operation83
During Breaks (E.g. Delays Caused by Material Trucks)83
During Longer Breaks (E.g. Lunch Break)83
When Work Is Finished84
Malfunctions86
Problems During Paving86
Paver Finisher Malfunctions88
E Set-Up and Modification91
Special Notes on Safety91
Distribution Auger92
Height Adjustment92
Mechanical Adjustment with Ratchet93
Hydraulic Adjustment (O)93
Auger Extension94
Screed95
Electrical Connections95
Connect Remote Controls95
Connect Levelling System95
Connect Auger Limit Switches96
Connect Levelling Device96
Connect Working Lights96
F Maintenance97
Notes Regarding Safety97
Maintenance Intervals98
Daily (or Every 10 Operating Hours)99
Weekly (or Every 50 Operating Hours)101
Annually (or Every 1000 Operating Hours)103
Every 2 Years (or Every 2000 Operating Hours)105
Points for Checking, Lubricating and Draining Oil106
Checkpoints107
Planetary Gear Conveyor (1)107
Batteries (2)108
Air Filter (Dry Air Filter) (3)108
Track Tension of Caterpillar Drive (4)109
Pump Distributor Gear (5)110
High-Pressure Hydraulic Filter (6)110
Conveyor Drive Chains (8)111
Outer Auger Bearing (9)112
Auger Box Filling Level (11)113
Auger Drive Chains (12)114
Conveyor Drive (13)114
Diesel Engine (17)115
Conveyor Deflection Rollers (20)115
V-Belts (21)115
Chain Tension, Conveyor (27)117
General Visual Inspection118
Check by a Specialist118
Fuel Tank (22)120
Hydraulic Oil Reservoir (25)120
Hydraulic Oil122
Filling Volumes123
Electric Fuses124
Main Fuses (1)124
Fuses in the Main Terminal Box124
Fuses on Operating Panel126

Dynapac F6C - Page 125

Table of Contents

Related product manuals