Eldes ESIM384 - Page 46

46
46
EN
ESIM384 Installation and Conguration Manual v1.1
Arm the system
Enter user/master code:
uumm → OK
Value: uumm – 4-digit user/master code.
• Partitioned system - arming a single partition – When a valid user or master code is entered, the keypad will display the partition
selection menu. Once a partition that is to be armed is selected, the system will initiate exit delay. During the exit delay, the keypad’s
buzzer will emit short beeps and the keypad will display ARMING part-name message for 3 seconds followed by partition selection
menu. When the keypad back-light timeout expires, the home screen view will follow. If
key is touched twice during exit delay, the
keypad will return to home screen view and display the countdown timer next to the partition name that is being armed.
Arm the system
Enter user/master code and select partition:
uumm → OK → [p] part-name → OK or OK → uumm → OK → ARM/DIS PARTITION → OK → [p] part-
name → OK
Value: uumm – 4-digit user/master code; p – partition number, range – [1... 4], part-name – up to 15
characters partition name
• Partitioned system - arming multiple partitions simultaneously – When a valid user or master code is entered, the keypad will
display the partition selection menu. Once ARM ALL menu item is selected the system will proceed as follows:
• if all partitions are disarmed-ready (no violated zone/tamper), the system will initiate exit delay. During the exit delay, the keypad’s
buzzer will emit short beeps and the keypad will display multiple ARMING part-name messages for 3 seconds reecting each
partition the user/master code is assigned to, followed by partition selection menu.
• if one or more partitions are disarmed unready (contains violated zone/tamper), the system will initiate exit delay. During the exit
delay, the keypad’s buzzer will emit short beeps and the keypad will display ARMING part-name message (-s) reecting ready
partition (-s), while the unready partition (-s) will be skipped indicated by part-name NOT READY message (-s) followed by
partition selection menu. Each message will be displayed for 2 seconds and corresponds to the partition (-s) the user/master code
is assigned to.
• if a combination of armed and disarmed-ready partitions exist, the system will initiate exit delay. During the exit delay, the keypad’s
buzzer will emit short beeps and the keypad will display ARMING part-name message (-s) seconds reecting ready partition (-s),
while the pre-armed partition (-s) will be skipped. Each message will be displayed for 2 seconds and corresponds to the partition (-s)
the user/master code is assigned to.
When the keypad back-light timeout expires, the home screen view will follow. If
key is touched twice during exit delay, the keypad will
return to home screen view and display the countdown timers next to the partition names the keypad is assigned to.
Arm all partitions
simultaneously
Enter user/master code:
uumm → OK → ARM ALL → OK or OK → uumm → OK → ARM/DIS PARTITION → OK → ARM ALL → OK
Value: uumm – 4-digit user/master code.
When successfully armed:
• the countdown timers will disappear.
• in addition, the keypad may display
icon next to the partition name that has been armed (by default – disabled).
Enable/disable Show
ARMED status in
keypad
ELDES
Cong-
uration
soft-
ware
This operation may be carried out from the PC using the ELDES Conguration software.
NOTE: If the user fails to enter a correct user/master code 10 times in a row, the system will block the keypad for 2 minutes and the
keypad will display KEYPAD BLOCKED message. While the keypad is blocked, the system prevents from entering any user/master code.
The keypad will automatically unblock once the 2-minute time has expired and display KEYPAD UNBLOCKED message
12.3.2. Cancelling System Arming
To cancel the arming process:
• Non-partitioned system – Enter the user/master code again during exit delay countdown.
• Partitioned system – Select the partition again, that is currently being armed, from the partition selection menu during exit delay
countdown. The keypad will display part-name ARMING TERMINATED message for 2 seconds followed by partition selection menu.
12.3.3. Disarming the System and Turning OFF the Alarm
To disarm and turn OFF the alarm, enter any out of 29 available 4-digit user codes or master code using the number keys on the keypad. By
default, the system disarming process is as follows:
• Non-partitioned system – When a valid user or master code is entered, the keypad will switch to home screen view.