Eldes ESIM384 - GSM CONNECTION AND ANTENNA STATUS MONITORING; GSM Connection Status Monitoring

109
109
EN
ESIM384 Installation and Conguration Manual v1.1
22. GSM CONNECTION AND ANTENNA STATUS MONITORING
22.1. GSM Connection Status Monitoring
The system supervises the GSM connection every 10 minutes. When the GSM connection loss is detected, the system indicator NETW will
light OFF and the system will attempt to restore the GSM connection. In case the system fails to restore the GSM connection within a 3-min-
ute period (by default), the keypad will indicate the system fault condition (see 29. INDICATION OF SYSTEM FAULTS) and the system will
continue the attempt to restore the GSM connection. In addition, the system may turn ON a determined PGM output to indicate the GSM
connection loss fault (by default - disabled).
Once the GSM signal restores, the system may notify the listed user by SMS text message (by default - disabled), the keypad will no longer
indicate system fault and the determined PGM output will turn OFF (if set up).
By default, the notications by SMS text message regarding GSM signal loss is disabled. To enable/disable this notication, please refer to
the following conguration methods.
Enable GSM
Connection Failed
notication
EKB2
Menu path:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → GSM CONNECT FAILED → OK
→ GSM USER 1... 10 → OK → ENABLE → OK
SMS text message to all users simultaneously: ... → GSM CONNECT FAILED → OK → SMS TO
ALL → OK → ENABLE → OK
SMS delivery report: ... → GSM CONNECT FAILED → OK → SMS REPORT → OK → ENABLE → OK
Value: iiii – 4-digit installer code.
EKB3/
EKB3W/
EWKB4
Enter parameter 25/21/55, event number, user phone number slot and parameter
status value:
User phone number: 25 11 up 1 #
SMS text message to all users simultaneously: 21 11 1 #
SMS delivery report: 55 11 1 #
Value: up - user phone number slot, range - [01... 10].
Example: 21111#
ELDES
Cong-
uration
software
This operation may be carried out from the PC using the ELDES Conguration software.
Disable GSM
Connection Failed
notication
EKB2
Menu path:
User phone number: OK → iiii → OK → SMS MESSAGES 2 → OK → GSM CONNECT FAILED → OK
→ GSM USER 1... 10 → OK → DISABLE → OK
SMS text message to all users simultaneously: ... → GSM CONNECT FAILED → OK → SMS TO
ALL → OK → DISABLE → OK
SMS delivery report: ... → GSM CONNECT FAILED → OK → SMS REPORT → OK → DISABLE → OK
Value: iiii – 4-digit installer code.
EKB3/
EKB3W/
EWKB4
Enter parameter 25/21/55, event number, user phone number slot and parameter
status value:
User phone number: 25 11 up 0 #
SMS text message to all users simultaneously: 21 11 0 #
SMS delivery report: 55 11 0 #
Value: up - user phone number slot, range - [01... 10].
Example: 2511020#
ELDES
Cong-
uration
software
This operation may be carried out from the PC using the ELDES Conguration software.
By default, the PGM output for GSM signal loss indication is not set. To set the PGM output and delay duration for GSM signal loss indication,
please refer to the following conguration method.
Manage GSM signal
loss indication by PGM
output
ELDES
Cong-
uration
software
This operation may be carried out from the PC using the ELDES Conguration software.
For more details on how Send SMS text message to all users simultaneously and SMS Cascade parameters aect the SMS text massage
transmission, please refer to 27. SYSTEM NOTIFICATIONS.