7800/7700 MultiFrame Manual
7814 Series Dual HDTV Up/Down/Cross Converters
Revision 1.1.3 Page - 75
Full Raster
Converts the full input raster to full output raster. If the
input and output aspect ratios are not equivalent, there will
be aspect distortion.
User 1 to User 10
There are 10 custom user slots available for custom
aspect ratios (See Section 7.10). Converts the region of
the input raster defined by the Input H & V Start and Stop
values to the region of the output raster defined by the
Output H & V Start and Stop values with coloured side
panels.
4:3 Side Panel to 16:9 TB Cut
13:9 Letter Box to 16:9 TB Cut
14:9 Letter Box to 16:9 TB Cut
13:9 Stretch to 16:9 TB Cut
14:9 Stretch to 16:9 TB Cut
16:9 Stretch to 16:9 TB Cut
These settings convert the input picture to 16:9 top and
bottom cuts. Note: For 1080i/1035i inputs, these
functions only work in field mode.
13:9 Stretch to 4:3 Side Panel
14:9 Stretch to 4:3 Side Panel
16:9 Stretch to 4:3 Side Panel
These settings squeeze common stretched input video
back to 4:3 side panel images on a 16:9 aspect raster.
4:3 to 4:3 Side Panel on 16:9
4:3 to 13:9 Stretch on 16:9
4:3 to 14:9 Stretch on 16:9
4:3 to 16:9 Stretch on 16:9
4:3 to 13:9 Crop on 16:9
4:3 to 14:9 Crop on 16:9
4:3 to 16:9 Crop on 16:9
These settings are common up-converter settings for
converting 4:3 aspect ratio images to common 16:9
formats. These settings are not appropriate for cross or
down conversion.
16:9 to 16:9 Letter Box on 4:3
16:9 to 14:9 Letter Box on 4:3
16:9 to 13:9 Letter Box on 4:3
16:9 to 4:3 Side Cut on 4:3
16:9 to 4:3 Squeeze on 4:3
These settings are common down converter settings for
converting 16:9 aspect ratio images to common 4:3
formats. These settings are not appropriate for cross or up
conversion.
16:9 Top Letter Box on 4:3 to 16:9
14:9 Top Letter Box on 4:3 to 16:9 TB Cut
14:9 Top Letter Box on 4:3 to 14.9 Side Panel
14:9 Top Letter Box on 4:3 to 16:9 Stretch on 16.9
16:9 Top Letter Box on 4:3 to 16:9
14.9 Letter Box on 4:3 to 16:9 TB Cut
14:9 Letterbox on 4:3 to 14.9 Side Panel
14.9 Letterbox on 4.3 to 16.9 Stretch on 16.9
4.3 Side Panel on 16.9 to 4:3
14.9 Side Panel to 14.9 Letter Box on 4:3
14.9 Side Panel to 4:3 Side Cut on 4:3
14.9 Side Panel to 4.3 Squeeze on 4.3
NOTE: When the module is configured to operate with AFD, (AFD Input Enable is set to
Enable and AFD is present on the input video signal) this control will have no effect.
As each of the above settings is selected, a pictorial representation of the selected conversion is shown to
the immediate right of the drop down menu as shown in Figure 7-21.
To Next Page
Loading...
