Fagor 8055i FL EN - Page 4

·4·
Operating manual
CNC 8055
CNC 8055i
SOFT: V02.2X
3.4 Turning cycle ................................................................................................................. 86
3.4.1 Data definition (levels 1 and 2) .................................................................................. 89
3.4.2 Data definition (levels 3, 4 and 5) .............................................................................. 91
3.4.3 Basic operation (levels 1 and 2)................................................................................. 93
3.5 Facing cycle................................................................................................................... 95
3.5.1 Data definition (levels 1 and 2) .................................................................................. 98
3.5.2 Data definition (levels 3, 4 and 5) .............................................................................. 99
3.5.3 Basic operation (levels 1 and 2)............................................................................... 101
3.6 Taper turning cycle ...................................................................................................... 103
3.6.1 Definition of data ...................................................................................................... 104
3.6.2 Basic operation ........................................................................................................ 107
3.7 Rounding cycle ............................................................................................................ 109
3.7.1 Geometry definition.................................................................................................. 110
3.7.2 Basic operation ........................................................................................................ 113
3.8 Threading cycle ........................................................................................................... 115
3.8.1 Geometry definition.................................................................................................. 118
3.8.2 Standard threads ..................................................................................................... 124
3.8.3 Basic operation. Longitudinal threading................................................................... 132
3.8.4 Basic operation. Taper threading............................................................................. 133
3.8.5 Basic operation. Face threading .............................................................................. 134
3.8.6 Basic operation. Thread repair................................................................................. 135
3.9 Grooving cycle ............................................................................................................. 136
3.9.1 Calibration of the grooving tool ................................................................................ 138
3.9.2 Geometry definition.................................................................................................. 139
3.9.3 Basic operation. Grooving........................................................................................ 143
3.9.4 Basic operation. Cut off............................................................................................ 145
3.10 Drilling and tapping cycles ........................................................................................... 146
3.10.1 Geometry definition.................................................................................................. 148
3.10.2 Drilling cycle. Basic operation .................................................................................. 150
3.10.3 Tapping cycle. Basic operation ................................................................................ 151
3.10.4 Multiple drilling cycle. Basic operation ..................................................................... 152
3.10.5 Multiple threading cycle. Basic operation................................................................. 153
3.10.6 Multiple slot milling cycle. Basic operation............................................................... 154
3.11 Profiling cycle............................................................................................................... 155
3.11.1 Level 1. Profile definition.......................................................................................... 156
3.11.2 Levels 2, 3 and 4. Profile definition .......................................................................... 158
3.11.3 Level 2. Optimizing of the machining of a profile ..................................................... 159
3.11.4 Definition of geometry levels 1 and 2. ZX profile ..................................................... 160
3.11.5 Definition of geometry at levels 3 and 4. XC, ZC profiles ........................................ 163
3.11.6 Basic operation at levels 1 and 2. ZX profile............................................................ 164
3.11.7 Basic operation at levels 3 and 4. XC, ZC profiles................................................... 165
3.11.8 Example. Level 1 ..................................................................................................... 166
3.11.9 Examples. Level 2.................................................................................................... 167
CHAPTER 4 Y AXIS
4.1 Profiling cycles with Y axis........................................................................................... 177
4.2 Graphics: XY and ZY plane selection .......................................................................... 177
4.3 Tool calibration ............................................................................................................ 178
CHAPTER 5 OPERATING IN ISO MODE
5.1 Editing blocks in ISO mode.......................................................................................... 182
5.2 Programming assistance ............................................................................................. 183
5.2.1 Zero offsets and presets .......................................................................................... 183
5.2.2 Work zones .............................................................................................................. 183
5.2.3 Insert labels and repetitions from label to label........................................................ 183
5.2.4 Mirror image............................................................................................................. 184
5.2.5 Scaling factor ........................................................................................................... 184