FOR-A MFR-3000 - Available Conversions; Conversion Settings; Converting 3 G SQD Input to 2 SI (MFR-8 SDIGB)

70
7-2. Available Conversions
 MFR-8SDIGB cards allow following input conversion settings:
From
To
Lock
Delay(H)
(*3)
Total Delay
(*4)
Ancillary
Data
12G-SDI
3G Quad (2SI)
Line lock
(*1)
0.3H~1H
0 frame + ** (H)
Through
Mask
Genlock
0.3H~1H
0 frame + ** (H)
1 frame + Delay (H)
0.5H to 1H
1 frame + 0H
12G-SDI
3G Quad (SQD)
Line lock
(*1)(*2)
Genlock
0.3H~1H
1 frame + Delay (H)
3G Quad (2SI)
3G Quad (SQD)
3G Quad (SQD)
3G Quad (2SI)
0.5H to 1H
1 frame + 0H
 MFR-8SDOGB cards allow following output conversion settings:
From
To
Lock
Delay(H)
(*3)
Total Delay
(*4)
Ancillary Data
3G Quad (2SI)
12G-SDI
Line lock
(*1)
0.3H~1H
0 frame + ** (H)
Through
Mask
Genlock
0.3H~1H
0 frame + ** (H)
1 frame + Delay (H)
0.5H to 1H
1 frame + 0H
3G Quad (SQD)
12G-SDI
Line lock
(*1)(*2)
Genlock
0.3H~1H
1 frame + Delay (H)
3G Quad (2SI)
3G Quad (SQD)
3G Quad (SQD)
3G Quad (2SI)
0.5H to 1H
1 frame + 0H
(*1) SDI signal input to the D connector is used as reference. When SDI Input Lock is selected on
MFR-8SDOGB cards, video signals are synchronized by inputting signals to all four channels in
gearboxes.
(*2) Available only on Gearboxes 2.
(*3) Delay (H) and Total Delay (H) indicate amount of delay and their settings correspond to the following
adjustable ranges.
Delay (H) Setting
Adjustable range
Delay (H) Setting
Adjustable range
0.3H
-0.8H to +0.2H
0.8H
-0.3H to +0.7H
0.4H
-0.7H to +0.3H
0.9H
-0.2H to +0.8H
0.5H
-0.6H to +0.4H
1H (1)
-0.1H to +0.9H
0.6H
-0.5H to +0.5H
1H (2)
-0.5H to +0.5H
0.7H
-0.4H to +0.6H
(*4) If Total Delay (frame) is set to “0 frame” for both gearboxes, the different Total Delay (H) setting is
available for the gearboxes.
If Total Delay (frame) is set to “1 frame” for either one or both gearboxes, the same Total Delay (H)
setting is required for the gearboxes: 1 frame + 0H or 1frame + Delay (H).
7-3. Conversion Settings
In the Web GUI, specify the Gearbox input and output formats, and then assign input/output
physical channels to logical channels. Use Link Settings that allow simultaneous 4-channel
operation and facilitate crosspoint switches.
7-3-1. Converting 3G SQD Input to 2SI (MFR-8SDIGB)
MFR-8SDIGB
MFR-3000
routing
Gearbox 1
Quad Link
3G-SDI
(SQD)
Quad Link
3G-SDI
(2SI)