Fuji Electric Frenic Mega Series - Page 201

5.2 Function Code Tables
5-20
Drive control
Code Name Data setting range
Change
when
running
Data
copying
Default
setting
V/f
PG
V/f
w/o
PG
w/
PG
To rq ue
control
Refer to
 page:
r
43 Speed Control 4
(Speed command filter)
0.000 to 5.000 s Y Y 0.020 N Y Y Y N
―
r
44 (Speed detection filter) 0.000 to 0.100 s Y* Y 0.005 N Y Y Y N
r
45 P (Gain) 0.1 to 200.0 times Y* Y 10.0 N Y Y Y N
r
46 I (Integral time) 0.001 to 9.999 s
999: Integration disabled
Y Y 0.100 N Y Y Y N
r
47 (Feed Forward Gain) 0.00 to 99.99 s Y* Y 0.00 N N Y Y N
r
48 (Output filter) 0.000 to 0.100 s Y Y 0.002 N Y Y Y N
r
49 (Notch filter resonance frequency) 1 to 200 Hz Y Y 200 N N N Y N
r
50 (Notch filter attenuation level) 0 to 20 dB Y Y 0 N N N Y N
r
51 Cumulative Motor Run Time 4 0 to 9999
(The cumulative run time can be modified or reset in units of 10 hours.)
N N - Y Y Y Y Y
r
52 Startup Counter 4 Indication for replacement (0000 to FFFF (hex.)) Y N - Y Y Y Y Y
r
53 Motor 4 (%X correction factor 1) 0 to 300% Y Y1, Y2 100 Y Y Y Y Y
r
54 (%X correction factor 2) 0 to 300% Y Y1, Y2 100 Y Y Y Y Y
r
55 (Torque current under vector control) 0.00 to 2000 A N Y1, Y2 *6 N N Y Y Y
r
56 (Induced voltage factor under
vector control)
50 to 100% N Y1, Y2 *6 N N Y Y Y
r
57 Reserved *9 0.000 to 20.000 s Y Y1, Y2 *6 - - - - -
Table 5.2-13
 J codes: Application Functions 1
Drive control
Code Name Data setting range
Change
when
running
Data
copying
Default
setting
V/f
PG
V/f
w/o
PG
w/
PG
To rq ue
control
Refer to
 page:
J01 PID Control (Mode selection) 0: Disable
1: Enable (Process control, normal operation)
2: Enable (Process control, inverse operation)
3: Enable (Dancer control)
N Y 0 Y Y Y Y N 5-214
J02 (Remote command )
0: Enable
/ keys on the keypad
1: PID command 1 (Analog input terminals [12], [C1], and [V2])
3: UP/DOWN
4: Communications link
N Y 0 Y Y Y Y N 5-215
J03 P (Gain) 0.000 to 30.000 times Y Y 0.100 Y Y Y Y N 5-219
J04 I (Integral time) 0.0 to 3600.0 s Y Y 0.0 Y Y Y Y N
J05 D (Differential time) 0.00 to 600.00 s Y Y 0.00 Y Y Y Y N
J06 (Feedback filter) 0.0 to 900.0 s Y Y 0.5 Y Y Y Y N
J08 (Pressurization starting frequency) 0.0 to 500.0 Hz Y Y 0.0 Y Y Y Y N 5-223
J09 (Pressurizing time) 0 to 60 s Y Y 0 Y Y Y Y N
J10 (Anti reset windup) 0 to 200% Y Y 200 Y Y Y Y N 5-225
J11 (Select alarm output) 0: Absolute-value alarm
1: Absolute-value alarm (with Hold)
2: Absolute-value alarm (with Latch)
3: Absolute-value alarm (with Hold and Latch)
4: Deviation alarm
5: Deviation alarm (with Hold)
6: Deviation alarm (with Latch)
7: Deviation alarm (with Hold and Latch)
Y Y 0 Y Y Y Y N
J12 (Upper level alarm (AH)) -100% to +100% Y Y 100 Y Y Y Y N
J13 (Lower level alarm (AL)) -100% to +100% Y Y 0 Y Y Y Y N
J15 (Stop frequency for slow flowrate) 0.0 (Disable): 1.0 to 500.0 Hz Y Y 0.0 Y Y Y Y N 5-226
J16 (Slow flowrate level stop latency) 0 to 60 s Y Y 30 Y Y Y Y N 5-226
J17 (Starting frequency) 0.0 to 500.0 Hz Y Y 0.0 Y Y Y Y N
J18 (Upper limit of PID process output) -150% to +150%; 999 (Depends on setting of F15) Y Y 999 Y Y Y Y N 5-227
J19 (Lower limit of PID process output) -150% to 150%; 999 (Depends on setting of F16) Y Y 999 Y Y Y Y N
J21 Dew Condensation Prevention
(Duty)
1 to 50% Y Y 1 Y Y Y Y Y
J22 Commercial Power Switching
Sequence
0: Standard sequence
1: Automatically switched by inverter alarm
N Y 0 Y Y N N Y 5-122
5-227
J56 PID Control
(Speed command filter)
0.00 to 5.00 s Y Y 0.10 Y Y Y Y N 5-228
J57 (Dancer reference position) -100% to 0% to 100% Y Y 0 Y Y Y Y N
J58 (Detection width of dancer position
deviation)
0: Disable switching PID constant
1 to 100%: Manually set value
Y Y 0 Y Y Y Y N
J59 P (Gain) 2 0.000 to 30.000 times Y Y 0.100 Y Y Y Y N
J60 I (Integral time) 2 0.0 to 3600.0 s Y Y 0.0 Y Y Y Y N
J61 D (Differential time) 3 0.00 to 600.00 s Y Y 0.00 Y Y Y Y N
J62 (PID control block selection) 0 to 3
bit 0: PID output polarity
0: Plus (add), 1: Minus (subtract)
bit 1: Select compensation factor for PID output
0 = Ratio (relative to the main setting)
1 = Speed command (relative to maximum frequency)
N Y 0 Y Y Y Y N
*6 The motor parameters are automatically set, depending upon the inverter's capacity. See Table 5.2-18.
*9 These function codes are reserved for particular manufacturers. Do not access these function codes.