GRAPHTEC CE7000-130AP - Page 256

I-2
L
LANGUAGE SELECTION ...................... 10-2
LCD contrast setting ......................... 10-12
LENGTH UNIT ............................... 10-3
Loading Media ................................ 2-8
M
Main Specications ............................ A-2
Media ....................................... 2-8
MEDIA ..................................... 2-27
Media auto prefeed ........................... 2-31
Media ange ................................. 1-5
Media guide .................................. 1-5
Media guide bar .............................. 1-5
Media sensors ........................... 1-4, 10-4
Media set lever ............................... 1-4
Media stocker ................................ 1-4
Media stopper ................................ 1-5
MEM. ...................................... 2-27
MENU Screen ............................... 2-27
Menu Tree ................................... A-5
Model ID response ........................... 11-7
Move away the tool carriage ..................... 3-5
Move in steps manually ......................... 3-3
Move the Tool Carriage and Media ................ 3-3
Moving Speed ................................ 8-9
N
Network (LAN) interface ........................ 9-2
Network (LAN) Interface connector ............... 1-5
Nomenclature ................................ 1-4
O
Oil-based ballpoint pen ......................... 1-2
Oil-based ballpoint pen plunger .................. 1-2
Operation key ............................... 2-24
ORIGIN .................................... 2-24
P
Panel Cutting ................................ 4-16
Pause key select setting ...................... 10-11
PAUSE/MENU ............................... 2-24
Pen holder ................................... 1-5
Pen station .............................. 1-5, 2-7
POSITION .................................. 2-25
Power cable .................................. 1-2
Power switch ................................. 1-4
Printing the Setting of the Plotter ............... 13-13
Priority of tool condition selection ................ 11-3
Push roller hold-down force switching lever ......... 1-5
Push rollers .................................. 1-4
Push roller sensors ........................... 10-5
R
Raise or Lower the Tool ........................ 3-2
Reading the error message ................... 13-23
Reading the screen ........................... 2-25
Removing a pen .............................. 2-7
Removing the tool ............................. 2-6
Replacing Cutter Blade ........................ 12-3
Reset ....................................... 3-6
Roll media ................................... 2-8
ROTATE ................................... 3-10
RS-232C ................................... 9-10
RS-232C interface ............................. 9-3
RS-232C interface connector .................... 1-5
S
Selecting Tool Condition ....................... 2-32
Self Diagnostic Test ......................... 13-21
SELF TEST ................................ 13-15
Setting Adjustment Between the Tools ............ 7-22
Setting a Separator ............................ 6-5
Setting a Time Out ............................ 6-3
Setting Cut Line Pattern ....................... 7-15
Setting cutting area ............................ 4-2
Setting cutting width ........................... 4-4
Setting Feeding Method ....................... 2-29
Setting Initial Blade Control Position Adjust ........ 7-19
Setting length of the page ....................... 4-5
Setting of the Initial Down Force .................. 7-6
Setting origin point when HP-GL is set ............. 3-9
Setting Paper Exposure Time ................... 6-16
Setting paper Ready time ....................... 4-8
Setting Rear Margin .......................... 6-12
Settings for Cutting ............................ 4-2
Setting step movement distance .................. 3-4
Setting the acceleration ....................... 2-41
Setting the command ......................... 11-2
Setting the Cutting Direction .................... 3-10
Setting the DHCP ............................. 9-5
Setting the force ............................. 2-40
Setting the length of overcut ..................... 7-4
Setting the number of pre feeds .................. 4-7
Setting the Number of Pre Feeds ................ 6-14
Setting the OFFSET FORCE ................... 7-21
Setting the Origin Point ......................... 3-7
Setting the space rear .......................... 4-9
Setting the speed ............................ 2-39
Setting the step size .......................... 11- 4
Setting the tangential mode ..................... 7-3
Setting the tool .............................. 2-36
Setting the tool condition ...................... 2-34
Setting tool No. .............................. 2-43
Setting user selection ......................... 9-14
SETUP MANUAL ............................. 1-2