IBM System/360 20 User Manual

.--,
this card and correct it if
necessary.
• Return the hopper deck to the
hopper.
• Press the start key of the affected
uni t.
• Press the start key on the CPU
console.
1 71 The read instruction that led to the
L--.J error hal t is re-executed upo n
.----.
restart.
• Remove the input deck from the pri-
mary hOFper.
• If the secondary hopper is also
used, remove the input deck from
the secondary hopper.
• Press the NPRO key.
• Remove the last three cards from
stacker 1 and place them in front
of the input deck for the primary
hopper.
• Check the card that is npw the
first card of the input deck for
the primary hopper (i.e., the card
that caused the error) and correct
it if necessary.
• If the secondary hopper is also
used, remove the last card from
stacker 5 and place it into the
secondary hopper.
• Return the input deck{s) to the
hopper (s) •
•
Press the start key of the 2560.
• Press the Start key on the CPU
console.
1 81 The read instruction that led to the
L--J error halt is re-executed upon
restart.
• Remove the input deck from the
secondary hopper.
• If the primary hopper is also used,
remove the input deck from the pri-
mary hopper.
• Press the NPRO key.
e Remove the last two cards from
stacker 5 and place them in front
of the input deck for the secondary
hopper.
• Check the card that is now the
first card of the input deck for
the secondary hopper (i.e., the
card that caused the error) and
correct it if necessary.
• If the primary hopper is also used,
remove the last two cards from
stacker 1 and place them into the
primary horper.
• Return the input deck(s) to the
hopper (s) •
•
Press the Start key of the 2560.
• Press the start key on the CPU
console.
r-,
I
91
•
Remove
the
deck from the
affected
L-J
hopper.
•
Check the first card
of the hopper
deck
(i. e. , the card that
caused
the check) •
•
Repair this
card or replace it
by
a
duplicate.
•
Return the
hopper deck to the
hopper •
•
P.ress the start
key of the affected
r--,
uni t.
• Press the start key on the CPU
console.
1101 The punch instruction that led to the
~J error halt is re-executed upon
.--,
restart.
• The mispunched card is the last
card in the stacker (stacker 2 for
the 2520). Remove this card from
the stacker and discard it.
• Press the start key on the CPU
console.
1111 The punch instruction that led to this
L __ J erLO.r halt is re-executed upon
.--,
restart.
• Mark the last card in stacker 1.
• Press the Start key on the CPU
console.
• Remove and discard the mispunched
card, i.e., the card stacked imme-
diately behind the marked card in
stacker 1 •
1121 The punch instruction that led to the
L--.J error halt is re-executed upon
.--,
restart.
• Mark the last card in stacker 5.
• Press the Start key on the CPU
console.
• Remove and discard the mispunched
card, i.e., the card stacked imme-
diately behind the marked card in
stacker 5.
1131 • Remove the hopper deck and open the
L __ J cover.
• Mark the card that is either imme-
diately before or in the read
station.
• Manually clear the feed path and
close the cover.
• Press the NPRO key to turn off the
Feed-Check light.
• Place the marked card and any cards
that followed it in the feed path
in front of the hopper deck.
• Place the cards that }receded the
marked card in the feed path into
Programmed-Halt Displays and Restart Procedures 111

IBM System/360 20 Specifications

General

Brand	IBM
Model	System/360 20
Category	Storage
Language	English