IBM System/360 20 - 150

r I ~ i ,
I Code I Cause 1 Restart I Ref. No.1
I
ESTR I I I I
,. I t_ I ~
I 1B56 IPhase has more than 9 subphases. IPress START on CPU to I 53 I
I-- I -f discontinue the job. I I
1
1657 1 MONTR sta tement encountered is not the I I I
I
Ifirst control statement, or two MONTR I I I
I
Istatements have been encountered. I I I
1---. I -1 I I
I 1B58 ITape Basic Monitor is incorrect. I I I
I-- I I -------+-----4
I 1B59 IAS5GN statements for tape Basic Monitor IPress START on CPU to continue I I
1
Ispecify more than 6 physical tape-drive Iprocessing. (The excess ASSGN I I
I
laddresses. I statements are ignored.) I J
I-- I -+- I ~
I 185A IREP card contains invalid hexadecimal IPress START on CPU to I 53 I
I
IcharacteI: (s) • I discontinue the jot. I 1
I-- I -+ I -f
1 1860 11st control statement is not a PRIOR I I 52 I
I
Istatement. I I I
I-- I --t I I
I
1861 IStatement read is not a control I I I
I I
sta temen t. 1 I I
~ I --t I 1
I
1B62 IControl statement contains invalid I I 1
1 I operation code. I I I
I-- I +- I ~
I 1B63 IPBIOR control statement contains invalidlOperator choice: I I
I I
opera nd. I a) Press ST ART on CPU to I 53 I
I-- I -4 discon tin ue t he job. I I
I
1864 I PlnOR statement is out of sequence. I b) Enter FF into location CE I (52) I
t--- I -f and press 5T ART on CPU to I I
I
1B65 IDELET control statement contains I continue processing. (The I I
I
linvalid operation code. I incorrect card is ignored. I I
t-----t_ -f A correct one may be I I
I
1B66 IDELET statement with operand ALL is I inserted as described in I I
I
Inot preceded by a PRIOR statement. I procedure 52.) 1 I
t I -+- t_----.
I 1B67 IDELET control statement or input macro IOperator choice: 1 I
I
Idefinition out of sequence. la) Press START on CPU to I 53 I
I I I
discon tin ue the job. I I
I I I
b) Enter FF into location CE I I
I 1 I
and press START on CPU to I I
I I I
continue processing. (The I I
I I I
DELET statement is ignored I I
I I I
or the macro definition is I I
I I I
skipped.) I I
J-- I --+- I -I
I 1B68 IElement in control statement (operation IOperator choice: I I
I
Icode or operand) is missing or extends la) Press START on CPU to I 53 I
I
Ibeyond column 71. I discontinue the job. I I
1 I Ib) Enter IF into location CE I (52) I
I I I
and press START on CPU to I I
I I I
con tin ue processing. (The I I
I I I
incorrect statement is I I
I I I
ignored. A correct one may I I
I
J I be inserted as described in I I
I I I
procedure 52.) I I
I-- I -+- I -I
I 1B69 I During write operation on SYSOOO or IOperator choice: I 58 I
I ISYSOPT,
end of reel is encountered. la) Press START on CPU to J 53 I
I I I
discontinue the job. I I
I I
Ib) Enter FF into location CE I I
I I I
and press START to continue I I
I I I
processing. (Only a few I I
I I I
records can be writ ten on I I
I I I
the tape.) J I
L--- I ..l.- ,
150 system/360 Model 20 TPS Operating Procedures