IBM System/360 20 - 144

r-- I ~ ~-------,
I Code ICause IRestart IRef.No.1
I ESTR I I I I
I-- I I t-------t
I OEAO IPermanent tape read error. IOperator choice: 57 I
~------t ~a) Press START on CPU to 53 I
I OEB1 IWhen fixed-length records are specified,1 discontinue the jot. I
lithe length of a block read is not an Ib) Enter IF into location CE I
I
linteger multiple of the specified recordl and press STABT on CPU to I
I
Ilength, or greater than the specified I continue processing. I
I
Iblock length. I ,
I-- I 1 ,
I OEB2 I When variable-length records are I I
I
Ispecified, the length of a block read I I
I I
is not equal to the block length I I
I lindicated in the block header, or I J
I Igreater than the maximum block length I I
I I
specified. I I
I-- I I -i
I OEC1 IWhen variable-length records are IPress StART on CPU to 57 I
I
,specified, the record length is O. Idiscontinue the job. 53 I
t---t 1 ,
I OEC2 IWhen variable-length records are , ,
I
Ispecified, the record length is I I
I
Igreater than the maximum record I I
I
Ilength specified. I I I
I----t_ I -+----i
I OEDO INext reel of file cannot be opened I Press START on CPU to I 53 I
I
Isince the OPEN routine has been Idiscontinue the job. I'
I loverlaid. I J I
I-- I -+- I --J
, 1A01 lEND card of input deck is not followed IPress START on CPU to continue I ,
I
Iby an end-of-file card. I processing. Check whether the I I
I I
Icard read after END card I I
I , I
belongs to next jot, and if I I
I ,
Iso, return it to the hopper. I ,
t----t_ , t_----~
I 1A02 I END card of inp ut deck is missing. I Follow procedure S3. (Check I 53 I
I I
Iwhether cards for the next job I J
I ) Ihave neen ejected £1 the NPBO, I I
I I
land if so, return them to their) I
I I
lhopper decks.) I I
I-- , t----------------------+----~
I 1A03 I Both NOLIST and NODECK have been IPress START on CPU to I 53 ,
I
,specified in AOPTN statement (s) • ,discontinue the jot. I'
I-- I t , ~
I 1A04 ,System tape is incomplete or damaged. IPress START on CPU to I 53 I
I , I
discontinue the job. (If the, I
I ,
lerror occurs repeatedly, a new I I
I I
Isystem tape must be created.) I ,
I-- I -+- -+----~
I 1A05 ILast card of input deck may have been IPress START on CPU to continue I I
I
Ipunched by mistake on 2520 Card Read- I processing. Check last card I I
I
IPunch or 2560. Istacked. If it has been I I
1 I IFunched, replace it by a I I
I I I
correct card. I I
J-----+------------------------+-----------------------f------J
I 1A06 ICard following END card of input deck I Press START on CPU to continue I I
I
Ihas teen misread and cannot ~e IFrocessing. Check whether the, ,
J lidentified. Icard read after ENt card I I
I I I
belongs to next job, and if so, I I
I I
Ireturn it to the hopper. I ,
l-- I t I I
, 1A1F IMacro definition not found in library. IPress START on CPU to I 53 I
, I
,discontinue the job. (If the I I
I I
lerror occurs repeatedly, a new I I
1 I Isystem tape must be created.) I ,
L--- __ ...l..- ~ I --I
144 System/360 Model 20 TPS Operating Procedures