IBM System/360 20 User Manual

IBM
~AAI S~MPL'E 3~
CARD GRQUPS
W92 AND W93
J ,U.CHING
t G!tAPHf(
I I
J
l'AGE
OF
NOGt ... _"·
DAlE
I INSTRUCTIONS
I Pl.NCH
I I I
ICAlD IUCIIO Nl/WII
STATfMENT
..... 1fIc.t' .. -
-
0 .... " ..
0,..-
C-
173
---
1 . 10
"
16
20
"
20
'15
40 015
50
"
60
"
71
/1
'J
I1
IE 7lA
If'P~
AlP
IE-
TrJ
-~
~Il
~'"
ER
J'N I'2N IAn
iIII
II
A~
,,",1,..lal
o.;,y
F:I ,.,
I .. ~
'9 82
'1"11
12
- I 1'01
,-iii:
~~
[Vl£
I=OR
r~
PllJT
I ..
If
II
--~
lu~
f"
AL
""Ie.
I'IA.
~171f
IN
JJ IJI
..,
...
/1
IllX E~
If
2~
,
-
II I
u11f
17'"
.. IF IFI ..
~~
('6
Ql.14
~)
I.IB
..:{
12
~)
,,0'"
1"'''''1
1
IV IE~ID
I'
""
l"4 ..,
IIJIUIL.
Figure 37. Job Control and Program Control Statements for Tape-to-Printer Job (Sorted
Records)
OPERATING PROCEDURES
The sample deck supplied by IBM is designed
for Model 20 systems with:
a) a storage caIlacity of 4096 bytes and the
following I/O devices:
an IBM 2560 !FCM,
an IEM 1403 Printer,
an IBM 2415 Magnetic Tape Unit Model 1
or 4 (9-track drives with unit numbers
80 and 81);
b) a minimum storage capacity of 8192 bytes
and the following I/O devices:
an IEM 2560 MFCM,
an IBM 1403 Printer,
an IBM 2415 Magnetic Tape Unit, any
model, (9-track drives with unit num-
bers starting at 80).
The following is a description of the
operating procedure for a configuration as
described under (~ above.
If the sample jobs are to be executed
with a different I/O configuration, the
ASSGN statements and the other job control
statements of the s~mple programs must be
chanyed according to the I/O
characteristics.
If the physical addresses of the user's
tape drive differ from the standard assign-
ments (780-785), the REP cards at the end
of the Monitor deck must be changed accor-
dingly. (See the description of the REP
cards in the SRL publication IB~_~y§!emL1&]
Mo~el-lQL_!~Eg-R.~Qgram~!rrY-~Y2iemL-ContrQ!
an~~_,gervice2£Q3.£am2, Form C24-9000.)
1. Mount a tape on the drive assigned to
SYSOOO (see ASSGN card in group X90) •
Press the Load-Rewind key and the Start
key of the drive.
2. Place the following cards into the hop-
per of the loading unit (2560 primary
hOfper in the example):
• the card IfL deck,
• the ASSGN card for SYSRDR (see group
X90), and
• the Basic Monitor card deck.
3. Place the following cards into the hop-
per of SYSRDR:
•
phases 00, 01 and 02 of the Job Con-
trol program deck,
• card group X90 (job control state-
ments -- excluding the ASSGN card
for S YS RES) ,
• phase 03 of the .Job Control program
deck,
• the Initialize-Tape Utility program
deck, and
• card group X91 (program control
statement) •
4. Press the Start key of the device.
5. Press the Reset key and the Start key
of the printer assigned to SYSLOG.
6. set the Address switches on the CPU
console to 009 C.
7. Press the Load key on the CPU console.
A standard volume label will be written
on the tafe mounted on drive SYSnoo. The
tape will be rewound so that the card-to-
tape job can be run next. The system halts
and code OB20 is displayed.
90 System/360 Model 20 TPS Operating Procedures
10

IBM System/360 20 Specifications

General

Brand	IBM
Model	System/360 20
Category	Storage
Language	English