IBM System/360 20 User Manual

.---,
1341 This halt code indicates one of the
L--J following conditions.
r-l
~ A check occurred during object pro-
gram execution.
• Empty both hoppers and all
stackers.
• Press the NPRO key.
• Mark the last card in stacker 1.
•• Place 6 blank cards into the
primary hopper.
• Press the Start key of the 2560.
• Press the start key on the CPU
console.
Operation is resumed, and an infor-
mation card is punched which con-
tains relevant details for restart
procedure 36. (See Figure 49 for
the format of the information
card.) If the halt was preceded by
a
punch-card or write-card instruc-
tion, the instruction(s) is (are)
re-executed and 1 or 2 correction
cards are produced. If a halt
occurs during the punching of the
information and correction cards,
follow the appropriate restart pro-
cedure, which is indicated by the
halt code. If no error condition
occurs, the system halts and the
code 0202 is displayed when the
information and correction cards
have been punched.
• When 0202 is displayed in the
E-S-T-R fields of the register
panel, perform restart procedure
36.
b) A check occurred after resuming
operation within this restart pro-
cedur.e (see (a) above).
• Empty the primary hopper and
press the NPRO key.
• Remove and discard all cards
following the marked card in
stacker 1.
• Continue with step 4 under (a)
above (step 4 is marked by
double bullets) •
1351
This halt indicates one of the follow-
L--J ing conditions.
a) A feed check (possibly combined
with other type(s) of error)
occurred during object program
execution.
• Empty both hoppers and all
stackE~rs.
• Open the cover.
• Manually clear the feed path and
close the cover.
• Press the NPRO key to turn off
the Feed-Check light.
• Stack all cards removed from the
.---,
feed path (cards from the pri-
mary hopper into stacker 1,
cards from the secondary hopper
into stacker 5), and check the
stacking sequence.
• DUFlicate and replace any
damaged cards.
• Mark the last card in stacker 1.
• continue with step 4 of restart
procedure 34a (step 4 is marked
by double bullets).
b) A feed check occurred after res~m
ing operation within restart proce-
dure 34.
• Empty the primary hopper and
open the cover.
• Manually clear the feed path and
close the cover.
• Press the NPRO key to turn off
the Feed-Check light.
• Discard all cards removed from
the feed path and all cards fol-
lowing the marked card in stack-
er 1.
• continue with step 4 of restart
procedure 34a (step 4 is marked
by double bullets).
1361 This halt indicates one of the follow-
L_-.J ing condi tions.
a) Restart 34 has been completed suc-
cessfully and the system is ready
for restart 36. (Upon restart 36,
object program execution is
resumed. )
• Empty the primary hopper.
• Press the NPRO key.
• Remove all cards following the
marked card from stacker 1.
tiscard any blank cards. The
card immedi~tely behind the
marked card is the information
card. The format of this card
is shown in Figure 37. The
information card may be followed
by 1 or 2 correction cards.
• If a rewritten correction card
was stacked behind the informa-
tion card, look for the last
card written before the halt
occurred. This card is either
the card that is now the first
card in the stacker s~ecified in
column 6 of the information card
or the last card of the deck
removed from the stacker speci-
fied in column 8 of the informa-
tion card. Check whether this
card contains entries
originating from earlier proces-
sing. If this is the case,
manually transfer these entries
to the rewritten correction
card. Replace the last card
written with the correction
116 System/360 Model 20 TPS Operating Procedures

IBM System/360 20 Specifications

General

Brand	IBM
Model	System/360 20
Category	Storage
Language	English