IBM System/360 20 User Manual

30. TPS Assembler program
(Part 2) •
*31. // END control statement.
32. TPS Input/Output and Basic
Monitor macro definitions,
with interspersed /1 PRIOR
and II CATAL statements, con-
cluded by a II END control
statement.
33. Separate set of /1 PRIOR and
// CATAL sta t.emen ts, con-
cluded by a /1 END control
statement.
34. TPS Input/Out.put macro
definitions for the .Binary
Synchronous Communications
Adapter, with interspersed //
PRIOR and /1 CATAL state-
ments, conclu.ded by a /1 END
control sta temen t.
35. separate set of /1 PRIOR and
II CATAL statements, con-
cluded by a 1/ END control
sta temen t.
36. TPS InputlOutput macro
definitions tor the IBM 1419
and 1259 Magnetic Character
Readers, with interspersed /1
PRIOR and /1 CATAL state-
ments, concluded by a /1 END
control statement.
37. Separate set of II PRIOR and
II CATAL statements, con-
cluded by // END control
statement.
OPERATING PROCEDURES FOR THE
DISTRIBUTION-PACKAGE RETRIEVAL PROGRAM
z
z
z
x
z
z
z
x
During execution, the Distribution-Package
Retrieval program:
• prints all header records together with
a message indicating the operator's out-
put specification, and
• if specified, lists the selected
element (s) (any other output is sup-
pressed), or
• punches the selected element(s) of the
distribution tape into cards, andlor
writes the selected element(s) with a Y
and z classification onto the assigned
output tape.
To execute the Distribution-Package Re-
trieval program, the following steps must
be taken.
1. Mount the distribution tape on a 2415
tape dri ve. (9-track t apes must be
mounted on 9-track drives; 7-track
tapes must be mounted on 7-track
drives. The data conversion feature is
required when using 7-track tapes.)
2. Press the Load-Rewind key and the start
key of the drive on which the distribu-
tion tape is mounted.
3. Place the IBM-supplied bootstrap card
and a blank card in the hopper of the
reading device (2501 if attached;
otherwise, 2520 Card Bead-Punch or
2560, hopper 1).
4. If punched output is required, place
blank cards in the hopper of the punch-
ing device. (Hopper 1 if 2560 is
used. )
5. Press START on each card I/O device
used.
6. set the Register-Data/Address switches
on the CEU console to OEOO.
7. set the ~ode switch on the CEU console
to PROCESS.
8. Press LOAD on the CPU console.
lial1-g~lg occurs after the bootstrap card
has been read into main storage. Continue
as follows:
9. Set the Mode switch on the CEU console
to STOR ALTER.
10. set the Data switches on the CPU con-
sole to the physical address of the
tape drive on which the distribution
tape is mounted (normally one of the
numbers 80-85).
11. set the Register-~ata/Address switches
to OOFC.
12. Press START on the CPU console.
13. Set the Mode switch to PROCESS.
14. Press START on the CPU console.
Halt OBF2 occurs after the Distribution-
Package-Retrieval program has been read
into main storage. continue as follow3:
15. Set the Mode switch to STOR ALTER •
16. Set the Register-~ata/Address switches
to OOFC.
17. Set the Data switches to
20 if a 2520 is used for punching
42 if a 1442 is used for punching
60 if a 2560 is used for punching
44 System/360 Model 20 TPS Operating Procedures

IBM System/360 20 Specifications

General

Brand	IBM
Model	System/360 20
Category	Storage
Language	English