IBM System/360 20 User Manual

r-1
detail in the SRL publication IBM
~y§te~L~2~_Moggl_l~~_1~£g_R£Qg£~m=
mi~YE!em~InEutLQy!£y!~on1£Ql
~§!g~, Form C24-9003.
)581 • Display register 13, which contains
L--J the displacement of the affected
symbolic device address (logical
unit block) from the beginning of
the logical unit table, and identi-
fy the tape drive concerned.
r-',
\591 Document feeding in the IB~ 1419 has
L_,J stopped. One of the following has
occurred:
Sort-Check Halt - 1419 Sort-Check
indicator-iiiia-Stop-Restore key are
illuminatedo
More than one or none of the stack-
er chute blades have been activated
for a document passing the selector
station. tocument ~eeding stoFs, and
the remaining documents in the docu-
ment path are read, stacker selected,
processed, and printed. The error
document is directed to the reject
pocket.
• Remove the error document from the
reject pocket.
• Follow the installation procedures
to identify the error document and
place the error document into the
correct pocket.
• Press the 1419 Stop-Restore key.
• Press the 1419 start key.
• Press the Start key on the CPU
console.
Q£~_Bal! - Left-Feed and/or Right-
Feed, ancl Stop-Restore key lights
are on ('1419).. Transport light is
on (1259).
• Follow the installation procedure
to determine which of the docu-
ments have been read.
• Place the documents that have been
read into the correct pockets.
Return all other documents to
the hopper in the proper order.
Place any mutilated documents
into the reject pocket.
• Press the Stop-Restore key on the
1419.
• Press the Start key on the 1419.
• Press the start key on the cpu.
If it is desired to discontinue the
job:
• Enter a hexadecimal value other
than '00' in the communication
byte (location X' OOCE') •
•
Press the Start key on the CPU
Console to initiate the end-of-
job routine.
r-,
\601. Remove the input deck from the
L--.J hopper
r-,
• Press the NPRC key
• Remove the last two cards from the
stacker and place them in front of
the input deck.
• Place the USER routine in front of
the input deck.
• Return the input deck to the hopper
• Press the start keys on the
affected units
• Press the Start key on the CPU
console.
1611 Too many follow-up documents were
L __ .J encountered after a disengage instruc-
tion, because the input buffer became
full.
r-,
• Press the stop key on the Magnetic
Character Reader.
• Press the Start key on the CPU to
continue processing.
• If this halt occurs frequently,
call in an lE~ Customer Engineer.
162\ A 1419 I/O error has occurred.
L __ .J Several unread documents may be in the
reject pocket.
r-,
• stop the 1419.
• Start the CPU and allow the user
program to print all the documents
that have been read.
• Return all rejected, unread docu-
ments to the feed hopper.
• start the 1419 to continue
processing.
• If the user program specified ERRE-
XI! in the 1419 file-definition
statement, the job can be discon-
tinued using the error exit option.
1631 • Check that the power to the Modem
L __ .J is on and that the connection to
the ESCA has been made proFerly.
• Check that the BSCA is ready.
• If the Autocall feature is used,
make sure that the receiver is on
the hook and that the Autocall unit
has power on.
• Set the Register-Data/Address
switch to the address OOCE.
•
set the Data switch to a value
other than zero.
• Set the Mode switch to STCR ALTER.
• Press STAET on the CPU to set the
CE byte to the value indicated by
the rata switch.
• Set the Mode switch to PROCESS.
•
Press START on the CPU.
If the frog ram does not continue and
error code 0501 is displayed again,
124 System/360 Model 20 TPS Operating Procedures

IBM System/360 20 Specifications

General

Brand	IBM
Model	System/360 20
Category	Storage
Language	English