IBM System/360 20 - UPDATING MODEL 20 TPS PROGRAMS FROM IBM-SUPPLIED PROGRAM MODIFICATIONS

When maintenance of the Model 20 Tape Pro-
gramming System is to be performed, the
revised elements are supplied on a tape
reel (or in cards). The retrieval of the
elements from such a distribution tape is
performed in the same way as for initial
retrieval.
The distribution tape may contain the
following items:
1. Distribution-Package Retrie-
va I prog ram.
2.
3.
4.
Any modified program phases
or programs for sequence num-
bers 2 to 13 of the initial
distribution tape.
The modified Tape-Resident
Control programs
Any modified program phases
or programs for sequence
numbers 16 to 30 of the
initial distribution tape.
If item 4 is present:
5. 1* control statement
6. II END control statement
7. Separate set of // CATAL
statements, concluded by the
/1 END statement.
8. Any modified InputlOutput
andlor Easic Monitor macro
definitions, with inters-
persed // PRIOR and II CATAL
statements, concluded by a II
END control statement.
If item 8 is present:
9. Separate set of II PRIOR
and 1/ CATAL statements, con-
cluded by a // END control
statement.
10. Any modified InputlOutput
macro definitions for the
Binary Synchronous Communica-
tions Adapter, with inters-
persed /1 PRIOR and II CATAL
statements, concluded by a /1
END control statement.
If item 10 is present:
11. Separate set of II PRIOR
and /1 CATAL statements, con-
Classi-
fi.f~ ti9J1
x
z
identical
to the
initial
release
z
x
x
z
x
z
x
cluded by a II END control
statement.
12. Any modified Input/Output
macro definitions for the IEM
1419 and 1259 Magnetic Char-
acter Beaders, with inters-
persed /1 PRIOR and 1/ CATAL
statements, concluded by a /1
END control statement.
If item 12 is present:
13. Separate set of 1/ fEICR
and II CATAL statements, con-
cluded by a 1/ END control
statement.
z
x
Updating of the initiall] distributed
Model 20 TPS programs is described in the
following paragraphs.
Q~~ling-21-R~Qg£~~§_Qn£~£-1iem_2_Qf-1h~
~istri~Ylion T~E~
All programs are card-resident. Replace
the corresponding card decks.
]~g~!1ng_Qi_I~Q9f~~§_Yn£~f_l1~~§_]_En£_~_gi
!~~_]1Elfi~~!iQn_I~E~
If the CMAINT program cannot be used on the
available machine configuration, the master
deck used for initial system generation
must be updated by replacing the corres-
ponding programs andlor phases. The new
system can be huilt as described in the
section ]~ilging the Initial S1st~12E~
1ro~_1~tl=§g£21i~g_RfQgf~~~
When the CMAINT program can be used on
the available machine configuration, u~dat
ing of the existing system tape is per-
formed as described in the section Q£~~!ing
1he_Prog£~ill-1i~£~L_~~~liQn_Q1-~_~1§lem
1~~.
The tape described in step 19 of the
section gEgf~!!ng_ffQ.f~dures fo£_l~§
~!E1fi~~!!Qn=~~~~~g§_]§lfi~XE1_lfggfE~ may
be used as input to the Cf.AINT program.
All control statements for the CMAIN! pro-
gram except the II fONTB and II ENt control
statements for the TPS Basic Monitor pro-
gram are made available under items 5, 6,
and 7 of the distribution tape. These
items are to be used under the following
conditions:
• If SYSIPT refers to a tape drive or a
card reader other than that assigned to
SYSRDR, item 7 of the distribution tape
provides the complete set of II CATAL
and II END statements. The 1* control
statement of item 5 must be placed
behind the last phase selected by the
user.
52 system/360 Model 20 TPS Operating Procedures