IBM System/360 20 - 148

r- I ------------------~i----------- 1-'
I Code ICause IRestart IRef.No.1
I ESTR I I I I
~ I -------------+1-- +------4
I 1B33 ITape mark has been read on SYSIPT. IOperator choice: I I
I I I a) Press START on CPU to I I
I I I continue processing with I I
I I I same reel. I I
I I
I b) Mount new reel and press I I
I I I START on CPU to continue I I
I I I processing. I I
1--- I -+ I -f
1 1B34. IInput records are out of sequence. IPress STABT on CPU to I 53 I
I I 1 discontinue the job. I I
I
t
--1B35 II First card column contains charact~r ~press STABT on CPU to cont-i-n-u-e~:-- 1
other than blank or 12-2-9, or -- 1f
I 'I I processing. (The card is I I
I I blank -- card is not a PHASE, ACTION, lignored.) I I
1-__ I or ENTRY card. I +--- __ ~
I 1B36 IREP card contains an incorrect I Press START on CPU to 53
I Ispecification. Idiscontinue the job.
1--- I -I
I 1837 ILoad address calculated from PHASE I
II Istatement is higher than 32,767. I
t-----t -I
I 1B38 11st input statement is not a PHASE I
I I statement. I
I- +--- -----------------1
I 1B39 INo TXT cards present for last phase. I
l- I ~
I 1B40 lEnd of reel reached on SYSOOO or I
I ISYSOPT. I
~ I +
---+-----1
I 1B41 lOuring read operation, tape mark IPress START on CPU to
58
53
I
I
I lencountered where not expected, or I discontinue the job.
I Irecord of incorrect length read. I
I
I- +_ I
I
1B42 ITape on SYSOOO is mispositioned. I Press STABT on CPU to
-t------t
I 53 I
I I (Hardware malfunction.) I discontin ue the job.
I I
)----+ -I
I 1B43 IThe same tape drive assigned to more
I Ithan one symbolic device address used,
1 lor no device assigned to required
I Isymbolic device address, or "data
I Iconverter off" specified for 7-track
I Itape drive.
)----+-
I 1B44 IName field of control statement contains
I lincorrect specification, or, if SYSIPT
I land SYSRDR refer to the same device,
I IPHASE statement is not preceded by a
I Icontrol statement.
~ I ,
I 1B45 IControl statement contains invalid I
I loperation code. I
~ I ----------------1
I 1B46 11st operand or separator (,) or I
I I delimiter (blank) of control I
I I statement is incorrect. I
1----+ ~
I 1B47 12nd operand or separator (,) of control I
I Istatement is incorrect. I
I-----+- -t
I "IB48 13rd operand or separator (,) or deli- I
I I miter (blank) is incorrect. I
1-----+ ~
I 1B49 14th operand or delimiter (blank) is I
I
Ii ncorrect. I
L ___ ---'-
148 System/360 Model 20 TPS Operating Procedures
I I
I I
I I
I I
I I
I I
I I
+----1
Follow procedure 52 and correctl 52
or insert the control statementl
before returning the hopper I
deck to the hopper. I
I
I
I
I
I
I
J