IBM System/360 20 User Manual

~ T I ,
Code ICause IRestart IRef.No.1
ESTR I I I I
I +------------:---------------+----1
OE4A IDATE statement is missing. IAn EXEC statement has been I 52 I
I ,encountered. Follow procedure I I
I
152, but place a DATE card in I I
I Ithe hOfper of SYSBDB before, I
I I Ireturning the input deck. I I
~----+-------------~-----------_+------------------+------J
I OB4B ITPLAB statement is missing or not IDiscontinue the job. , 53 I
I I
in the correct flace. I I I
1-----+ I +------1
I OB4C ITPLAB statement is incorrect. I Discontinue the job. , 53 I
~ I -+ I -l
I OE4D ILabel-information area in main IDiscontinue the job. , 53 I
,
Istorage is full. (CONFG card incorrect I , I
I
lor too many TFLAB statements for the I I I
I lavailable storage capacity.) Or: a CONFGI I I
I
Icard is read in after the processing of , , I
I I
a tIe as ton e 'I P LAB s tat e men t . I I I
I----+_ +-------------------------+--------1
I OB4E ISYSIPT has not been assigned a tape IInsert a correct ASSGN card fori 52 I
I
Idrive, or oonvert feature is off ISYSIPT and an EXEC [CAtEE card, I
I I
(ignored when SYS1PT is assigned to I in the hopper of SYSRDR and I I
I I a tafe drive) I continue FIocessing. , I
J I +--------------------------+--------1
I OB4F IOn SYSIPT, a tape mark has been IDiscontinue the job. I 53 I
I
lencountered where not expected, or a I I I
I Irecord of incorrect length has been I I I
I I
read. I , I
I I
+--------------~--------+------__1
I OB64 IDevice assigned as SYSRDR is not IRepeat the 1PL procedure using I I
I
lattached Ithe frefer ASSGN statement for I I
I I ISYSRDR, I
~-----+ -+ I --1
I OE7A IOverlap has been specified for a IFress STAFT on the CPU console I 53 I
I
Imachine without the overlap feature Ito discontinue the job. I I
~------+ +_------------------------------+ I
I
OE7E IA system program has teen specified to ICferater choice: I I
I I
run in the overlap mode I a} Press START on the CPU , I
I I I
console to continue in non- I I
I I I
overlap mode. I I
I I I b) Enter FF into location CE I I
I I I
and press START on the CPU I I
I I
I console to aiscontinue the I I
I I I job. I I
~----+ I -+ -f
I OE7C IError statistics were requested but are ,Press the Start key on the CPU I I
I
Inot allowed with this job. Iconsole to enable normal I I
I I
lexecution of the job. Errer I I
I I
Istatistics will not be , I
I I
linitiated. I I
i----i-- +------------------------+----1
I OB7D IError statistics about the preceding IWhen error statistics are not
I job are requested, but a LOG contrel Irequired, press the Start key
I statement is missing. Ion the CPU console to continue
, Ithe job.
I IWhen error statistics are
I I required enter bexadecimal IF
I linto location OOCE to permit
I Iprinting of the error
I Istatistics. Then press the
1 I~tart key on the CPU console
I Ito continue the job.
I I (Check if aPfropriate paper is
I Ion the SYSLOG printer).
L _____ ..L
---i- ____________________________ i-- ____ _
Programmed-Halt Displays and Restart Procedures 135

IBM System/360 20 Specifications

General

Brand	IBM
Model	System/360 20
Category	Storage
Language	English