IBM System/360 20 User Manual

r-",
• Press the start key of the affected
unit.
• Press the start key on the CPO
console.
1221 The punch instruction that led to the
L __ J error halt is re-executed upon
r-,
restart.
• Remove the primary-hopper deck.
• If the secondary-hopper is also
used, remove the secondary hopper
deck.
• Open the cover.
• Manually clear the feed path and
close thE~ cover.
• Press the NPRO key to turn off the
Feed-Check light.
• Discard any blank cards removed
from the feed path.
• Place the punched cards removed
from the feed path and originating
from the primary hopper into stack-
er 1, in the proper order.
• If the halt code is 02D4, remove
the last card from stacker 1 and
discard it.
• If the secondary hopper is also
used, place the punched cards
removed from the feed path and o-
riginating from the secondary hop-
per into stacker 5, in the proper
order. Then remove the last card
from stacker 5 and place it into
the secondary hopper.
• Duplicate and replace any damaged
cards.
• Return the hopper deck~) to the
hopper (s) •
•
Press the start key of the 2560.
• Press the start key on the CPU
console.
1231 The punch instruction that led to the
L __ J error halt is re-executed upon
restart.
• Remove the secondary-hopper deck.
• If the primary hopper is also used,
remove tne primary-hopper deck.
• Open the cover.
• Manuallj clear the feed path and
close thE~ cover.
• Press the NPRO key to turn off the
Feed-Check light.
• Discard any blank cards removed
from the feed path.
• Place the punched cards removed
from the feed path and originating
from the secondary hopper into
stacker 5, in the correct order.
• If the halt code is 02D5, r~move
the last card from stacker 5 and
discard it.
• If the primary hopper is also used,
place the Funched cards removed
r-,
1241
L __ J
r-,
•
•
•
•
•
•
•
•
•
from the feed pat_ and originating
from the primary hopper into stack-
er 1, in the proper order. Then
remove the last two cards from
stacker 1 and place them into the
primary hopper.
Duplicate and replace any damaged
cards.
Return the hopper deck(s) to the
hOPFer (s) .
Press the start key of the 2560.
Press the start key on the CPU
console.
Remove the hopper deck(s) and open
the cover.
Manually clear the feed path and
close the cover.
Press the NPRO key to turn off the
Feed-Check light.
Discard any blank cards removed
from the feed path.
Place the punched cards removed
from the feed path (primary feed
for the 2560) into the appropriate
stacker (stacker 1 for the 2560),
in the proper order.
• If the affected unit is a 2560 and
the secondary hopper is also used,
place the punched cards removed
from the feed path and originating
from the secondary hopper into
stacker 5, in the proper order.
Then remove the last card from
stacker 5 and place it into the
secondary hopper.
• Duplicate and replace anl damaged
cards.
• Return the hopper deck(s) to the
hopper{s) •
•
Press the start key of the affected
unit.
• Press the start key on the CPU
console.
1251. Remove the secondary-hopper deck.
L __ J. If the primary hopper is also used,
remove the primary-hopper deck.
• Open the cover.
• Manually clear the feed Fath and
close the cover.
• Press the NPBO key to turn off the
Feed-Check light.
• Discard any blank cards removed
from the feed path.
• Place the punched cards removed
from the feed path and originating
from the secondary hopper into
stacker 5, in the proper order.
• Place the punched cards removed
from the feed path and originating
from the primary hopper into stack-
er 1, in the proper order. Then
remove the last two cards from
staGker 1 and place them into the
primary hopper.
114 System/360 Model 20 TPS Operating Procedures

IBM System/360 20 Specifications

General

Brand	IBM
Model	System/360 20
Category	Storage
Language	English