IBM System/360 20 User Manual

r---~ ----------~-------------------------------~------,
J Code
I ESTR
ICause I Restart IRef.No.1
I I 1 1
~
----~I- ------------------+1----------- +------~
1 1B4A
1
I
1
1
I
1B4B
1B4C
ITwo consecutive XFR or END cards have I Press START on CPU to continue I 1
1
been read, or a CAT AL sta tem,ent is I processing. (The second XFR or 1 I
1encountered after an end-of-file card lEND card or the CATAl 1 I
Ihas been read on SYSIPT. Istatement, respectively, is I J
1
I ignored.) I I
I
-+-------------------------------+------~
I PHASE sta tement is not followed by 1 Press START on CPU to I 53 1
IREP, TXT, XFR, or END cards. Idiscontinue the job. I I
I
t I ~
CATAL statement is encountered when Operator choice: J
tape mark has been read on SYSIPT. a} Press START on CPU to I 53
discontinue the job. I
b) Enter OF into location CE J
and press START on CPU to
continue processing. (The
CATAL statement is ignored.)
c) If the tape on SYSIPT con-
tains additional input,
leave it on the drive.
If further input is stored
on another tape, mount that
tape on SYSIPT. Enter FF
into location CE and press
S1ABT on CPU to continue
processing.
~----+ ------11---- +-------~
1 1B4D IPhase SYSEOJ is to be included I Press START on CPU to I 53 1
1 1
(replaced) and is not the first 1 discontinue the job. 1 1
J
Iphase in the input stream, or SYSEOJ I I I
I
1 has been read as operand in a DELET 1 I 1
1 I statement. I I I
I I -i I I
I 1B4E I Input phase or DELET statement out of I I I
I Isequence. 1 I I
1 I -i I I
I 1 B4F I PHASE statement contains invalid I 1 I
I loperands, or load address of a phase I I 1
I lis lower than end address of Basic 1 I I
I 1 Moni tor area, or colu mn 1 of PHASE I I I
I
1statement is not blank. I I I
t------t --t- ,-----111- 1
I 1B50 IPHASE statement contains phase name withlPress the START on CPU to 1 53 I
1 1illegal characters, or phase name Idiscontinue the job. I I
I Iconsists of more than 6 characters. I I I
I I ... 1 I
I 1B51 ILoad address in TXT or REP card is I 1 I
I, Ilower than load address of phase. I 1 I
I I -i I I
I 1 B52 I Load address of last byte in TXT or REP I I I
I
Icard is higher than 32,767. I J I
I I -i I I
I 1B53 I Phase or subphase consists of less than I 1 I
I
\24 bytes. I 1 I
I I t--------~ I ~
I 1B54 JPhase to be deleted not found in IPress START on CPU to continue I I
J Ilibrary. I processing. (DELET statement isl I
1 1 lignored.) I I
t I --+- +-----~
1 1B55 IPHASE statement not found where I Press START on CPU to continue I J
1 I expected. I processing. (Warning only.) 1 I
I
Programmed-Halt Displays and Restart Procedures 149

IBM System/360 20 Specifications

General

Brand	IBM
Model	System/360 20
Category	Storage
Language	English