IBM System/360 20 - 146

r I i -,--------,
I Code ICause I Restart IRef.No.1
I ESTR J I I I
I- . I I +------1
J lB06 13rd operand or separator (,) or I Correct the card containing I 52 I
I
Idelimiter (blank) of ASSGN statement Ithe statement and continued I I
I
lis incorrect. I processing. I I
I----t- -t I I
I lB07 14th ope:cand or delimiter (blank) of I I I
I
IASSGN statement is incorrect. I I I
I-- I + I i
I lBOS IASSGN statements for tape Basic Monitor IPress START on CPU to continue I I
I Ispecify more than 6 physical tape-drive I processing. (The excess ASSGN I I
I I
addresses. Istatements are ignored.) I I
1-------+ , +-------1
I lB09 ICONFG statement for tape Basic Monitor I Correct the card containing the, 52 I
I
lis incorrect. Istatement and continue I I
I I I
processing. I I
I-- I +---------------------+----i
I lBOA IPHASE statement for Job Control program IPress START on CPU to 53
I lis missing or misplaced. I discontinue the job.
I-- I -t
I lBOB IPHASE statement is incorrect or phases I
I
lare out of sequence. I
I-- I -t
I lBOC ILoad address for text in TXT or REP I
I
Icard is lower than load address of I
I
Iphase or higher than 32,767. I
I- I -I
I lEOD IPhase/subphase consists of less than I
I 124
bytes or SYSEOJ is the only input I
I I
phase. I
r I -t
I lBOE ILoad address of phase or subphase is I
I
Ilower than end address of Basic Monitor.1 J
I--- I -t I
I 1 BOF I Phase has more than 9 subphases. I J
r- I I -------r--~
I lB10 ITwo consecutive XFR or END cards have I warning only. Press START on I I
I I
been read. I CPU to conti nue processing. I I
I I I (The second XFR or EN!: card I I
I I
lis ignored.) I I
J----+_------. I --+-------1
J lBl1 ITape mark has been encountered on IOperator choice: I I
I
ISYSIPT. la) Press START on CPU to I I
I
I I continue processing with I I
I I I same reel. I I
I I I b) Mo un t new reel and press I I
I I I START on CPU to continue I I
I I I
processing. I I
I--- 1 -+-1 -- I -t
I 1B12 1 Specification in REP card is not IPress START on CPU to 1 53
I Ihexadecimal. Idiscontinue the job. 1
I--- 1 -t I
1 lB13 I Error statistics specified and not I I
I Ipossible with LDSYS. I I
I--- 1 -t I
I 1B21 IThe name used in an Assembler ENTRY I I
I Istatement is the same as that used in I I
I la preceding Assembler ENTRY statement. I I
J- , -t I
J 'lB22 I A phase name is the same as the name of I I
I I
a control secJ.ion or the name used in an I I
, IAssembler ENTRY or EXTRN statement. I I
l----+_ -I I
I lB23 IThe name used in an Assembler ENTRY I I
I
Istatement is the same as that of a I I
J Ipreceding control section. I I
146 system/360 Model 20 TPS Operating Procedures