IBM System/360 20 - 145

r----y-- --,- i -,
I Code ICause I Restart IRef.No. I
I
ESTR 'I I I I
j-----t_------------------------t- -+-----1
I 1ABA ICard punching device assigned to SYSOPT I Press START on CPU to continue J I
I I
is not at tached to the Model 20. I p::ocessing. (The object progra m I I
I I I is not punched out.) I I
I I +- I 1
I 1 ABB SYSIPT was in "not operational" IPress START on CPU to continue I I
I
condi ti on when it was att empted to I processing. Empty the hopper (s) I I
I
eject the last card into the stacker. lof the device assigned to I I
I ISYSIPT and press NPRC. Return I I
I
lany cards following the last I I
I
Icard to the hopper{s). Return I I
1 Ithe hopper decks. 1 I
I----t- -1-------------------+------1
1ACO SYSOOO Incorrect assignment. 1 Press START on CPU to 53 I
1AC1 SYS001 No physical device assigned Idiscontinue the job. 1
1AC2 SYS002 to required symbolic device I I
1ACA SYSOPT address, or tape drive 1 I
1ACB SYSIPT assigned to SY5IPT, or "data I I
converter off" specified for I I
7-track drive. I I
1ACE SYSLST
Conflicting assignment. I I
SYSLST is unassigned while 1
.AOPTN NOLIST is not 1
specified. I
r-----~I- ~
1ADO
1AD 1
1AD2
1ADA
1 AEO
1AE 1
1
AE2
1AEA
15Y5000 Tape drive has been assigned 1
I
SYSOO 1 to more than one symbolic I
ISY5002 device address used (other I
15YSOPT
than 5YS002 and SYSOPT). I
I -4
15YSOOO End of reel has been reached 1
15Y5001 during write operation. 1
ISYS002 I
ISYSOPT I
I -4
1AFO ISYSOOO Error condition during read I
1AF1 ISYS001 operation (incorrect-length I
1AF2 ISYS002 record, tape mark where not I
1AFF ISYSBES expected, wrong bl'ock number,1
1 I etc.) due to damaged tape. I
1-----+ ~
I 1BOO IThe same tape drive assigned to more I
I Ithan one symbolic device address used, I
1 lor no device assigned to required I
) Isymbolic device address, or "data I
I Iconverter offrt specified for 7-track I
I I
tape dri ve. I
j + ------------------1
1 1B01 ITape Basic Monitor is incorrect. 1
II+--
I 1B02 IControl statement read on SYSBDB is not ICorrect the card containing
I IASSGN, CONFG, or END statement. Ithe statement and continue
I I Iprocessing.
j-----t_ I
I 1B03 IControl statement on SYSIPT I Press STABT on CPU to
I Imisplaced or incorrect. Idiscontinue the job.
j------+__ 1
I 1B04 11st operand or separator (,) of ASSGN I Correct the card containing
I Istatement is incorrect. Ithe statement and continue
j-----__+__ -Ifrocessing.
I 1B05 12nd operand or separator (,) of ASSGN I
I Istatement is incorrect. I
L I !
52
-I
I
I
I
+-------1
I 53 I
1 1
+-------1
J 52 I
1 1
I 1
1 I
I 1
Programmed-Halt Displays and Restart Procedures 145