IBM System/360 20 User Manual

r---,
the stacker, in the correct order.
• Duplicate and replace any damaged
cards.
• Return the hopper deck to the
hopper.
• Press the Start key of the 2501.
• Press the start key on the CPU
console.
1141 The read instruction that led to the
L---I error halt is re-executed upon
r--,
restart.
• Remove the hopper deck and open the
cover.
• Mark the card that is either in or
immediately beyond the read sta-
tion. (This is the car d that
caused the read error.)
• Manually clear the feed path and
close the cover.
• Press the NPRO key to turn off the
Feed-Check light.
• Check the marked card and correct
it if required.
• Place the marked card and any cards
that followed it in the feed path
in front of the hopper deck.
• Place the cards that preceded the
marked card in the feed path into
the appropriate stacker, in the
correct order.
• Duplicate and replace any damaged
cards.
• Return the hopper deck to the
hopper.
• Press the start key of the affected
unit.
• Press the start key on the CPU
console.
1151 The punch instruction (and the pre-
~ ceding read instruction if the unit is
also used for reading) that led to the
error halt is re-executed upon
restart.
• Remove the hopper deck and open the
cover.
• Mark the card that is located imme-
diately beyond the punch station.
(This card may already be in the
stacker. )
• Manually clear the feed path and
close the cover.
• Press the NPRO key to turn off the
Feed-Check light.
• Place the marked card and all other
cards removed from the feed path in
front of the hopper deck, in the
proper order.
• Check the marked card. If it does
not contain any entries originating
from earlier processing, replace it
with a blank card. If it does con-
tain such entries, transfer these
r--,
entries to a blank card manually,
and replace the marked card with
the newly prepared card.
• If the affected unit is a 2520 card
read-punch, check the second card
of the hopper deck, which may have
been misread, and correct it if
necessary.
• Duplicate and replace any damaged
cards.
• Return the hopper deck to the
hopper.
• Press the start key of the affected
unit.
• Press the start key on the CPU
console.
1161. Remove the hopper deck and open the
L-.J cover.
r--,
• Manually clear the feed path and
close the cover.
• Press the NPRO key to turn off the
Feed-Check light.
• Place the card removed from the
pre-punch station into stacker 1 if
the halt code is 0211, and into
stacker 2 if the halt code is 0212.
• Place the card removed from the
pre-read station into the hopper.
• Duplicate and replace any damaged
cards.
• Return the hopper deck to the
hopper.
• Press the start key of the 2520.
• Press the Start key on the CPU
console.
)171. Remove the hopper deck and open the
L-.J cover.
r---,
• Mark the card that is either imme-
diately before or in the punch
station.
• Manually clear the feed path and
close the cover.
• Press the NPRO key to turn off the
Feed-Check light.
• Place the marked card and any cards
that followed it in the feed path
in front of the hopper deck.
• Place the cards that preceded the
marked card in the feed path into
the appropriate stacker, in the
proper order.
• Duplicate and replace any damaged
cards.
• Return the hopper deck to the
hopper.
• Press the Start key of the affected
uni t.
• Press the Start key on the CPU
console.
)181 • Remove the hopper deck and open the
L_J cover.
• Mark the following cards:
112 System/360 Model 20 TPS Operating Procedures

IBM System/360 20 Specifications

General

Brand	IBM
Model	System/360 20
Category	Storage
Language	English