IBM System/360 20 User Manual

•
Duplicate and replace any
damaged
cards.
•
Return the hopper deck(s} to the
hopper(s) •
•
Press the start key
of
the
2560.
•
Press the Start
key on the CPU
console.
r--1
1261 • Check the attached 1403 or 2203
L--J printer and, if an. error condition
exists, correct the condition.
(For the error conditions that may
occur and the corrective action
r--1
required, refer to the pertinent
SRL publica tions.)
• Press the Start key of the printer.
• Press the start key on the CPU
console.
1271 The print operption cannot be repeated
'--' to correct the error.
r--,
• Mark the misprinted line or correct
it manually.
• Press the Start key of the printer.
• Press the Start key on the CPU
console.
1281 The read instruction preceding the
'--' error halt is re-executed upon
restart.
•
Remove the hopper deck.
•
Press the NPRO key.
•
Place
the
last
two cards
stacked in
front of the hopper deck.
•
Correct
the first card of thE:!
hop-
per deck.
(This
is
the card con-
taining the error.)
•
Return the hopper
deck
to
the
hopper.
•
Press the
Start key of the affected
uni t.
•
Press the Start
key on the CPO
console.
r--,
1291
The
two
read ins tr uctions prececiing
'--'
the halt are r e- ex e cut e d upon
rE~start.
•
Remove
the hopper
deck.
•
Press the NPRO key.
•
Remove the last three cards from
the
stacker and
place
them
in
front
of the
hopper deck.
•
Correct the first card of
the
hop-
per
deck. (This is the card con-
taining the error).
•
Return
the hopper
deck to t h€~
hopper.
•
Press the Start key
of the 2501.
•
Press the
Start
key on
the CPU
r--,
1301 Proceed as described in restart proce-
L-..J dure 6. (Correct the card that fol-
r-,
lows the marked card. This card con-
tains the format error.)
1311 Proceed as described in restart proce-
L __ J dure 15. (Correct the card that fol-
r--,
lows the marked card. This card con-
tains the format error).
1321. Remove the hopper deck from the
L-..J hopper (primary hopper for the
2560.)
r-,
• If the affected unit is a 2560 and
the secondary hopper is also used,
remove the secondar]-hopper deck.
• Press the NPRO key.
• If the affected unit is a 2560,
remove the last three cards from
stacker 1 and place them in front
of the primary-hopper deck.
• If the affected unit is a 2520,
remove the last two cards from the
stacker and place them in front of
the hopper deck.
• Replace the card that is now the
first card of the hopper deck
(primary-hopper deck for the 2560)
with a blank card.
• If the affected unit is a 2560 and
the secondary hopper is also used,
remove the last card from stacker 5
and place it into the secondary
hopper.
• Return the hopper deck(s} to the
hopper (s) •
•
Press the Start key of the affected
uni t.
• Press the Start key on the CPU
console.
1331 • Remove the deck from the secondary
L __ J hopper.
• If the primary hopper is also used,
remove the deck from the primary
hopper.
• Press the NPRC key.
• Remove the last two cards from
stacker 5 and place them in front
of the secondary-hopper deck.
• Replace the card that is now the
first card of the secondary-hopper
d~ck with a blank card.
• If the primary hopper is also used,
remove the last two cards from
stacker 1 and place them into the
primar] hopper.
• Return the hopper deck(s) to the
hopper(s} •
•
Press the Start key of the 2560.
• Press the start key on the CPU
console. console.
Programmed-Halt Displays and Restart Procedures 115

IBM System/360 20 Specifications

General

Brand	IBM
Model	System/360 20
Category	Storage
Language	English