IBM System/360 20 User Manual

r------~ -------,- I ,
I Code ICause 1 Bestart IRef.No. I
I ESTR J J I I
.---+_ --t------------------+----~
1 OB31 IHardware malfunction or system tape I Be-initiate the system run I I
I I
misposi tioned. I (IPL) • I I
.--_.--+_ --------11'---, +------1
1 OB3A ILoad address for the program on IChange control cards -- either 1 I
I
Jthe system tape to te loaded is linsert correct address or I 1
1 Itoo low for execution in overlap Iremove the overlap specifica- 1 J
J 1 mode (lower than 2100) I tion. Assembly must l::e per- I 1
1 I Iformed again. I I
l-- I +------------------------+-------1
I 0838 ILoad address on the TXT card when Press START on the CPU 1
lithe LOADER function is specified console to discontinue I
I
lis lower than! the job. I
I
12000 for non-overlap mode and tape 1
1 I
input OR I
I
12100 for non-overlap mode and card I
I I
input OR I
I
12400 for overlap mode and tape I
I I
input OR I
J 12500 for overlap mode and card I
I I infu t. I
1-----+ I -J
I OE40 IPAUSE statement has been encountered. ISet uf job(s) as descril::ed. I
I I
IPress START to resume I
I I I
c Fer a ti 0 n • I I
I- I -+ +-----~
I OB41 11st operand or separator (,) or I 52
I Idelimiter (blank) of control I
I
Istatement is :incorrect. I
.---+------------------------------1
1 OE42 12nd operand or separator (,) or I
I
Jdelimitar (blank) of control I
I
Istatement is incorr~ct. I
I-- I -t
J OB43 J3rd operand or separator (,) or I
I I
delimiter (blank) of control I
I
Istatement is incorrect. I
l----+------------------------------~
I OB44 14th opera:nd or delimiter (blank) of I
I
Jcontrol statement is incorrect. I
.. ----+-----------------------------~
I OB45 ITape unit number specified in ASSGN I
I
Istatement is not in Basic Monitor. I
J
J
J
I
I
.---+-----------------------+- , 1 -t
I OB46 IJOB statement is missing. IFollow procedure 52, l::ut place
I 52 I
I I la JOE card in the hopper of
I I
I I ISYSBDR before returning the
I I
I I linput deck.
~ I +_
I OB47 ITwo successive JOB statements have been I
I
lencountered, i.e., no EXEC statement I
I
Ihas been encountered between two JOB I
1
Istatements. I
~ I +
I OB48 IThe card just read did not contain a I
I Icontrol statement. I
~-+-------------------------~
I OB49 IControl statement contains invalid I
I
loperation code, or TPLAB statement I
I
lis not preceded ty VOL statement. I
L ____ -L-- ____ _
--L.- __ _
134 System/360 Model 20 TPS Operating Procedures
I I
----+-----1
I 54 I
I I
J I
I I
-------+_------1
I 52 I
J I
I I
I I
I I
I I
-.l. _____ .J

IBM System/360 20 Specifications

General

Brand	IBM
Model	System/360 20
Category	Storage
Language	English