IBM System/360 20 User Manual

r--,
card A ~hich should be in the pre-
read station) ;
card B (which should be in the pre-
punch station) ;
card C (which should be the last
card in stacker 1 if the halt code
is 0231, or the last card in stack-
er 2 if the halt code is 0232).
The cards may be mispositioned. If
they are, try to locate them by
means of card numbers or other
identifiers.
• Manually clear the feed path and
c l,ose the cover.
• Press the NPRO key to turn off the
Feed-Check light.
• Check card C. If it contains
entries originating from earlier
processing, transfer these entries
to a blank card manually and place
the newly prepared card into the
hopper. If card C does not contain
any such entries, place a blank
card into the hopper. Discard card
C.
• Place card B and card A in front of
the hopper deck, so that card B is
the first card of the deck.
• Duplicate and replace any damaged
cards.
• Return the hopper deck to the
hoppe r.
• Press the start key of the 2520.
• Press the start key on the CPU
console.
)191 The read instruction that led to the
~ error halt is re-executed upon
restart.
• Remove the primary-hopper deck.
• If the secondary hopper is also
used, remove the secondary-hopper
deck.
• Open the cover.
• Mark that card from the primary
hopper which is either immediately
beyond or in the read station.
• Manuallj clear the feed path and
close the cover.
• Press the NPBO key to turn off the
Feed-Check light.
• Place the marked card and the two
cards from the primary hopper that
followed it in the feed path in
front of the primary-hopper deck.
• Ifcthe secondary hopper is also
used, place the card from the
secondary hopper that was located
before the read station in front of
the secondary-hopper deck.
• Stack any other cards removed from
the feed path as required.
• Check the marked card, which may
have been misread, and correct it
if necessary.
• Duplicate and replace any damaged
r-,
cards.
• Return the hopper deck(s) to the
hopper (s) •
• Press the start key of the 2560.
• Press the Start key on the CPU
console.
1201 The read instruction that led to the
L __ J error halt is re-executed upon
r--,
restart.
• Remove the secondary-hopper deck.
• If the primary hopper is also used,
remove the primary-hopper deck.
• Open the cover.
• Mark the card from the secondary
hopper that is either immediately
beyond or in the read station.
• Manually clear the feed path and
close the cover.
• Press the NPRO key to turn off the
Feed-Check light.
• Place the marked card and the card
from the secondary hopper that fol-
lowed it in the feed path in front
of the secondary-hopper deck.
• If the primary hopper is also used,
place the two cards from that hop-
per that were located before the
read station in front of the
primary-hopper deck.
• Stack any other cards removed from
the feed path as required.
• Check the marked card, which may
have been misread, and correct it
if necessary.
• Duplicate and replace any damaged
cards.
• Return the hopper deck(s) to the
hopper(s) •
• Press the Start key of the 2560.
• Press the Start key on the CPU
console.
1211 The punch instruction that led to the
~ error halt is re-executed upon
restart.
• Remove the hopper deck and open the
cover.
• Manually clear the feed path and
close the cover.
• Press the NPRO key to turn off the
Feed-Check light.
• Discard all blank cards removed
from the feed path.
• Stack any punched cards removed
from the feed path as required.
• If the halt code is 02D4 or 03D4,
remove and discard the last card
stacked. (This card may have been
misp unched.)
• Duplicate and replace any damaged
cards.
• Return the hopper deck to the
hopper.
Programmed-Halt Displays and Restart Procedures 113

IBM System/360 20 Specifications

General

Brand	IBM
Model	System/360 20
Category	Storage
Language	English