IBM System/360 20 User Manual

.----,
• Press the Start key on the CPU
console.
c) The incorrect card was read on the
2560 secondary feed.
• Remove the input deck from the
secondary hopper.
• If the primary hopper is also
used, remove the input deck frem
the primary hopper.
• Press the NPRO key.
• Remove the last two cards from
stacker 5 and place them in
front of the input deck for the
secondary hOFper.
• Check the card that is now the
first card of the input deck for
the secondary hopper (i.e., the
card that caused the error) and
correct it if necessary_
• If the primary hopper is also
used, remove the card(s) ejected
by the NPRO from stacker 1 and
place it (them) into the primary
hopper.
• Return the input deck~) to the
hopper (s) •
•
Press the start key of the 2560.
• Press the start key on the CPU
console.
No!~: When the program is running
under control of a card-resident sys-
tem, the job control statements must
precede phase 02 of the Job Control
program deck.
If the incorrect card is a loader
card, place the control cards in front
of phase 02 of the Job Control program
deck, before returning the input
deck (s) to the hopper (s) •
1531. Remove the hopper deck(s).
L __ J • Press the NPRO key.
.--,
• set up the I/C devices for the next
job.
• Press the Start keys of all I/O
devices to be used.
• Press the start key on the CPU
console.
1541 Both JOB cards are ignored.
L--.J. Remove the input deck from the hop-
per of SY SR I:R.
•
If SYSRDR refers to the primary or
secondary feed of a 2560 and the
other feed is also used, remove the
other hopper deck, too.
• Press the NPRO key.
• Remove the job control cards read
during this Job Control run (i.e.,
all cards up to, and including, the
first of the two JOB cards read)
from the stacker of SYSBDR (stacker
1 for 2560 primary feed, stacker 5
for 2560 secondary feed).
• Place the JOB card and all other
r--,
jeb control cards required for the
next job into the hopper of SYSRDR.
• Make
sure that the last control
card is an EXEC card.
• Check the first cards of the input
deck previously removed from the
hepper. If they are object program
cards, return the input deck to the
hopper. If they are job control
cards for the next-but-one job,
(which can be the case only when
the tape-resident Job Control pro-
gram is being executed), check
whether the JOB card is missing.
If so, the second JCE card read is
probably for this job. Place this
JOE card and all job control cards
that followed it in the stacker
into the hopper of the device
assigned to SYSRDR and return the
input deck to the hopper.
• If the device is a 2560 and the
other feed is also used, return the
cards ejected from that feed by the
NPBC to the hopper, and return the
hopper deck to the hopper.
• Press the start key of the device.
• Press the start key on the CPU con-
sole to resume operation.
1551 If it is desired to discontinue the
L __ J job,
• prepare the I/O devices for the
next job and
• press the Start key on the CPU con-
sole to initiate the end-of-jot
routine.
If it is desired to continue the job,
take the following steps:
• Remove the hopper deck from the
affected device.
• If the device is the 2560 primary
or secondary f~ed and the other
feed is also used, remove the deck
from the other hopper.
• Press the NPRO key of the device.
• a) If the device is a 2501 and an
additional input area has not
been specified in the BPG con-
trol card (i.e., col. 22 is
blank), remove the last two
cards from the stacker.
b) If the device is a 2501 and an
additional input area has been
sFecified in the BPG control
card (i.e., col. 22 contains a
E), remove the last three cd!:ds
from the stacker.
c) If the device is a 2520 Card
Read-Punch, remove the last two
cards stacked.
d) If the device is the 2560 pri-
mary feed, remove the last three
cards from stacker 1.
e) If the device is the 2560 secon-
122 System/360 Model 20 TPS Operating Procedures

IBM System/360 20 Specifications

General

Brand	IBM
Model	System/360 20
Category	Storage
Language	English