IBM System/360 20 - 133

r-----~--------------------------------------~----------------~ I'
I Code ICause IBestart IRef.No.1
I ESTR I I I I
.------+----------------------------------+-------------------------------+----1
I OB01 IControl statement other than ASSGN IRepeat the If I procedure using I
I
Ifollows IPL. Ithe correct control statement. I
~------+---------------------------------------~ I
I OB02 IASSGN statement following IPL is not I I
I I
for SYSRDR. I I
.-----+-----------------------------------~ I
I OB03 IIncorrect 'cuu' specification in ASSGN I I
I I
s ta te me n t. I I
.------+-------------------------------------1 I
I OB04 IIncorrect 'dd' specification in ASSGN I I
I I statement. I I
.------+--------------.----------.--------~ I
I OB11 IIPL is not followed by a control I I
I I
s ta te me n t • I I
r----+-----------------------------------_t I
I OB12 ITape IPL is followed ty a control I I
I Istatement other than ASSGN. I I
~------+--------------------------------------~
I OB13 11st operand or separator (,) of A~SGN I
I
Istatement is incorrect. I
.-----+-----------------------------------1
I OB14 12nd operand or separator (,) of ASSGN I
I
Istatement is incorrect. I
~------+------------------------------------_t
I OB15 13rd operand or separator (,) or I I
I
Idelimiter (blank) of ASSGN statement I I
I
I is incorrect. I I
~-----+----------------------------1 I
I OB16 14th operand or delimiter (blank) of I I
I IASSGN statement is incorrect. I I
I I I -+------1
I OB17 ITape drive for system tape is 7-track orlCorrect the error condition andl I
I
Inot ready, or not file-protected. The Irepeat the IPL procedure. I I
I
Imounted reel either is not the system I I I
I
Itape or it contains records of wrong I I I
I Ilength. I I I
~ I +--------------------------+-----1
I OB18 IBasic Monitor does not contain unit IRepeat the IPL procedure using I I
I
Inumber specified in ASSGN statement. la set of correct REP cards. I I
I I + ---+-----1
I OB19 I End-of-file card missing, or cards ctherlRepeat the IPL procedure using I I
1 Ithan ASSGN SYSRDR or REP cards between Ithe required cards in the I I
I I ASSGN SYSRES card and end-of-file card. I correct sequence. I I
~----+ -\----------------------+--------1
I OB1A IUnit number in REP card is zero. I Correct the BEP card(s) and I I
I I I releat the IPL procedure. I I
~----+------------------------------_+__------------------------+-------J
I OB20 IEnd-of-job halt. Ifrepare the next job(s). fress I I
I I
1ST AR Ton CPU. I I
~----+ -+-------------------------+------1
I OB30 IPhase not found. Name of phase to be IIf error in JCE statement, I 52
I Iloaded next is not in core-image Iccrrect and re-insert JCB card,1
I I directory. (Error in JOB statement or I then press START on CfU to I
I
lerror in FETCH macro instruction of Icontinue processing. I
I I
problem program.) I If error in FETCH m,acro in- I
I I
Istruction, discontinue the job.1
I I l]g!gl This halt may also occur I
I I
lafter an error halt in the I
I I
IAssembler, CMAINT, ~MAINT, or I
I I
IDSERV program. In this case, a I
I I I
new IPL procedure is required. I
L ______ ~ I ~ _____ _
Programmed-Halt Displays and Restart Procedures 133