EasyManuals Logo

Juniper EX3300 Complete Hardware Guide

Juniper EX3300
218 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #106 background imageLoading...
Page #106 background image
Figure 27: Sliding the Rear Mounting-Blade into the Side Mounting-Rail
3—1— SwitchRear mounting-blade
2—Side mounting-rail
10. Attach the rear mounting-blades to the rear post by using the appropriate screws for
your rack. Tighten the screws.
11. Ensure that the switch chassis is level by verifying that all the screws on the front of
the rack are aligned with the screws at the back of the rack.
Related
Documentation
Connecting Earth Ground to an EX Series Switch on page 99
Connecting AC Power to an EX3300 Switch on page 105
Connecting DC Power to an EX3300 Switch on page 107
Connecting and Configuring an EX Series Switch (CLI Procedure) on page 119
Mounting an EX3300 Switch in a Recessed Position in a Rack or Cabinet on page 90
Rack-Mounting and Cabinet-Mounting Warnings on page 164
Mounting an EX3300 Switch in a Recessed Position in a Rack or Cabinet
You can mount an EX3300 switch in a rack or cabinet such that the switch is recessed
inside the rack from the rack front by 2 inches. You can use the 2-in.-recess front brackets
provided in the separately orderable four-post rack-mount kit to mount the switch in a
recessed position.
Reasons that you might want to mount the switch in a recessed position include:
You are mounting the switch in a cabinet and the cabinet doors will not close completely
unless the switch is recessed.
The switch you are mounting has transceivers installed in the uplink ports—the
transceivers in the uplink ports protrude from the front of the switch.
Copyright © 2015, Juniper Networks, Inc.90
Complete Hardware Guide for EX3300 Ethernet Switches

Table of Contents

Other manuals for Juniper EX3300

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Juniper EX3300 and is the answer not in the manual?

Juniper EX3300 Specifications

General IconGeneral
Ethernet LANYes
Authentication methodRADIUS, TACACS+
Connectivity technologyWired
Ethernet interface typeGigabit Ethernet
Number of VLANs4096
Networking standardsIEEE 802.1ab, IEEE 802.1D, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3x, IEEE 802.3z
Ethernet LAN data rates10, 100, 1000 Mbit/s
Copper ethernet cabling technology1000BASE-T, 100BASE-TX, 10BASE-T
Console port-
ExpressCard slotNo
Fiber ports quantity4
USB 2.0 ports quantity0
Basic switching RJ-45 Ethernet ports quantity48
Throughput130 Mpps
Number of queues8
MAC address table16000 entries
Maximum data transfer rate176 Gbit/s
Supported data transfer rates10, 100, 1000Mbps
Switch typeManaged
Switch layerL2
Security algorithmsSSH-2
Power sourceAC
AC input voltage100 - 240 V
Power consumption (typical)100 W
Form factor1U
Product colorBlack
Flash memory1024 MB
Processor frequency1000 MHz
Compatible operating systemsJunos
Operating altitude0 - 3049 m
Non-operating altitude0 - 4877 m
Storage temperature (T-T)-40 - 70 °C
Operating temperature (T-T)0 - 45 °C
Storage relative humidity (H-H)0 - 95 %
Operating relative humidity (H-H)10 - 85 %
Supported network protocolsIPv6
Weight and Dimensions IconWeight and Dimensions
Depth310 mm
Width437 mm
Height44 mm
Weight4900 g

Related product manuals