Keithley 2002 User Manual

IEEE-488 Reference
3-57
:FREQuency
:COUPling AC|DC
:COUPling?
:REFerence <n>
:STATe <b>
:STATe?
:ACQuire
:REFerence?
:DIGits <n>
:DIGits?
:SOURce <name>
:SOURce?
:THReshold
:CURRent
:RANGe <n>
:RANGe?
:LEVel <n>
:LEVel?
:VOLTage
:RANGe <n>
:RANGe?
:LEVel <n>
:LEVel?
:TTL
Path to configure frequency:
Specify input coupling.
Query input coupling.
Specify reference (0 to 15e6).
Enable or disable reference.
Query state of reference.
Use input signal as reference.
Query reference value.
Specify measurement resolution (4 or 5).
Query resolution.
Select source: (CURRent or VOLTage).
Query source.
Path to configure threshold:
Path to set current threshold:
Specify range (0 to 1).
Query range.
Specify threshold level.
Query threshold level.
Path to set voltage threshold:
Specify range (0 to 1000).
Query range.
Specify threshold level.
Query threshold level.
Set threshold to TTL level.
AC
0
OFF
5
VOLTage
0.001
0
10
0
3.18.7
3.18.9
3.18.10
3.18.15
3.18.16
:TEMPerature
:APERture <n>
:AUTO <b>
:AUTO ONCE
:AUTO?
:APERture?
:NPLCycles <n>
:AUTO <b>
:AUTO ONCE
:AUTO?
:NPLCycles?
:REFerence <n>
:STATe <b>
:STATe?
:ACQuire
:REFerence?
:DIGits <n>
:AUTO <b>
:AUTO ONCE
:AUTO?
:DIGits?
Path to configure four-wire resistance:
Set integration rate in seconds (166.67e-6 to 1).
Enable or disable auto aperture.
Enable and then disable auto aperture.
Query auto aperture.
Query aperture (integration rate).
Set integration rate (line cycles; 0.01 to 50).
Enable or disable auto NPLC.
Enable and then disable auto NPLC.
Query auto line cycle integration.
Query line cycle integration rate.
Specify reference; -200 to +1821 (°C)
Enable or disable reference.
Query state of reference.
Use input signal as reference.
Query reference value.
Specify measurement resolution (4 to 7).
Enable or disable auto resolution.
Enable and then disable auto resolution.
Query auto resolution.
Query resolution.
(Note 2)
OFF
1
OFF
0
OFF
6
ON
3.18.5
3.18.6
3.18.9
3.18.10
Table 3-10 (Continued)
SENSe command summary
Command Description
Default
parameter SCPI Ref.

Keithley 2002 Specifications

General

Resolution	8.5 digits
DC Voltage Accuracy	±0.0006%
Maximum DC Voltage	1000 V
Maximum AC Voltage	750 V
Maximum DC Current	3 A
Maximum AC Current	3 A
Connectivity	GPIB, RS-232
DC Voltage Range	100 mV to 1000 V
AC Voltage Range	100 mV to 750 V
Resistance Range	10 Ω to 1 GΩ
Model	2002
Category	Multimeter
Interface	GPIB, RS-232
AC Current Accuracy	±0.1%
Frequency Range	0.1Hz to 300kHz
Display	VFD
Type	Digital
Power Supply	100-240V AC, 50/60Hz
Current Range (DC)	100 μA to 3 A
Current Accuracy (DC)	±0.01%
Current Range (AC)	100 μA to 3 A
Current Accuracy (AC)	±0.1%
DC Current Range	100 μA to 3 A
AC Current Range	100 μA to 3 A