Keithley 2002 User Manual

F
Features 1-1
Filter 2-71
Filter modes 2-71
Filter types 2-71
Frequency 2-32
Front panel aspects of IEEE-488
operation 3-5
Front panel operation 2-1
Front panel scanner controls 2-77
Functions 2-9
G
GENERAL 2-99
General bus commands 3-4
General information 1-1
GET (group executive trigger) 3-5
GPIB 2-96
GTL (go to local) 3-5
H
Halting triggers 2-50
High energy circuit safety precautions 2-4
HP3458A emulation mode H-1
I
IEEE-488 conformance information E-1
IEEE-488 bus connections 3-1
IEEE-488 bus overview D-1
IEEE-488 primary address 2-4
IEEE-488 reference 3-1
IEEE-488 status indicators 3-5
IFC (interface clear) 3-4
Information messages 2-7
Inspection 1-2
Interface function codes B-1
Introduction 1-1, 2-1, 3-1
L
LIMITS 2-97
Line fuse replacement 2-2
Line power connections 2-1
LLO (local lockout) 3-4
LOCAL key 3-6
M
Manual addenda 1-2
Manual ranging 2-40
Math 2-75
Maximum readings 2-40
Menu 2-87
Multiple display of rel 2-41
Multiple displays 2-4
N
Navigating menus 2-9
O
Options and accessories 1-2
P
Percent 2-76
Percent deviation 2-76
Polynomial 2-75
Power-on default conditions 2-4
Power-up 2-1
Power-up sequence 2-2
Primary address selection 3-2
Programming syntax 3-23
Q
Queues 3-16
QuickBASIC 4.5 programming 3-3
R
Range 2-40
RANGe commands 3-96
Relative 2-40
REN (remote enable) 3-4
Response time 2-73
RTCLock commands 3-157
S
Safety symbols and terms 1-2
SAVESETUP 2-90
Scanner operation examples 2-83
Scanning 2-77
Scanning overview 2-77
SCPI conformance information F-1
SDC (selective device clear) 3-5
Selecting and configuring math 2-76
Sense subsystems 3-91
Signal oriented measurement
commands 3-41
SPE, SPD (serial polling) 3-5
Specifications 1-2, A-1
Starting and stopping scanning 2-83
Status and error messages 2-7
Status byte and service request (SRQ) 3-16
STATUS-MSG 2-99
Status structure 3-6
Storing and recalling readings 2-69
T
TCONfigure commands 3-155
Temperature 2-33
TEST 2-97
THReshold commands 3-107
Transition filters 3-8
Trigger Link 2-53
Trigger model 2-41
Trigger model (IEEE-488 operation) 3-18
Trigger subsystem 3-152
Triggers 2-41
Two and four-wire resistance 2-28
U
Using CHAN key to close and open
internal channels 2-78
Using CONFIGURE CHAN to configure
channels 2-79
Using CONFIG-SCAN to configure
scanning 2-80
Using SCAN to configure scan
parameters 2-81
W
Warm-up period 2-4
Warranty information 1-2
i-2

Keithley 2002 Specifications

General

Resolution	8.5 digits
DC Voltage Accuracy	±0.0006%
Maximum DC Voltage	1000 V
Maximum AC Voltage	750 V
Maximum DC Current	3 A
Maximum AC Current	3 A
Connectivity	GPIB, RS-232
DC Voltage Range	100 mV to 1000 V
AC Voltage Range	100 mV to 750 V
Resistance Range	10 Ω to 1 GΩ
Model	2002
Category	Multimeter
Interface	GPIB, RS-232
AC Current Accuracy	±0.1%
Frequency Range	0.1Hz to 300kHz
Display	VFD
Type	Digital
Power Supply	100-240V AC, 50/60Hz
Current Range (DC)	100 μA to 3 A
Current Accuracy (DC)	±0.01%
Current Range (AC)	100 μA to 3 A
Current Accuracy (AC)	±0.1%
DC Current Range	100 μA to 3 A
AC Current Range	100 μA to 3 A