Parameter Typical Return
(none) <number of points>
Step 0 - 99, *RST 0 (none)
Returns the number of currentBOSTpoints: ARB:CURR:UDEF:BOST:POIN? (@1)
Returns the number of voltage BOST points: ARB:VOLT:UDEF:BOST:POIN? (@1)
Returns the number of BOST points for step 0: ARB:SEQ:STEP:CURR:UDEF:BOST:POIN? 0,(@1)
[SOURce:]ARB:CURRent:UDEFined:DWELl <value>{<,value>},(@<chanlist>)
[SOURce:]ARB:CURRent:UDEFined:DWELl? (@<chanlist>)
[SOURce:]ARB:VOLTage:UDEFined:DWELl <value>{<,value>},(@<chanlist>)
[SOURce:]ARB:VOLTage:UDEFined:DWELl? (@<chanlist>)
Specifies the dwell time for each user-defined current Arb point. A comma-delimited list of up to 511
points may be programmed. Dwell time is the time that the output will remain at a specific point. Dwell
times can be programmed from 0 through 262.144 seconds with the resolution shown in the table
below:
[SOURce:]ARB:SEQuence:STEP:CURRent:UDEFined:DWELl <value>{<,value>}, <step#>, (@<chanlist>)
[SOURce:]ARB:SEQuence:STEP:CURRent:UDEFined:DWELl? <step#>, (@<chanlist>)
[SOURce:]ARB:SEQuence:STEP:VOLTage:UDEFined:DWELl <value>{<,value>}, <step#>, (@<chanlist>)
[SOURce:]ARB:SEQuence:STEP:VOLTage:UDEFined:DWELl? <step#>, (@<chanlist>)
Specifies the dwell time for each user-defined current Arb point for Arb Sequence steps. The last value
in the sequence is the step number.
Range in seconds Dwell resolution Range in seconds Dwell resolution
All Models except N678xA Models N678xA only
0 - 0.262144 1 microsecond 0 - 0.268435 1.024 microsecond
0 - 2.62144 10 microseconds 0 - 2.68435 10.24 microsecond
0 - 26.2144 100 microseconds 0 - 26.8435 102.4 microsecond
0 - 262.144 1 millisecond 0 - 268.435 1.024 millisecond
Parameter Typical Return
0 - 262.144 (all except N678xA SMU)
0 - 268.435 (N678xA SMU only
*RST 1 pointwith a valueof 0.001
<dwell time>
Step 0 - 99, *RST 0 (none)
Program a currentdwell list: ARB:CURR:UDEF:DWEL 0.1,0.2,0.3,0.4,0.5,(@1)
Program a voltage dwell list: ARB:VOLT:UDEF:DWEL 0.1,0.2,0.3,0.4,0.5,(@1)
Program a dwell listfor step 0: ARB:SEQ:STEP:CURR:UDEF:DWEL 0.1,0.2,0.3,0.4,0.5, 0,(@1)
7 SCPI Programming Reference
260 Keysight N6705C Operating and Service Guide
To Next Page
Loading...
