Korg Triton-Rack

Appendices
231
File contains unsupported data
File is read-only protected
File unavailable
File/path not found
Front sample data used in rear sample
Can’t overwrite
I
Illegal file description
Illegal SMF data
Illegal SMF division
Illegal SMF format
M
Measure size over limit
Medium changed
Medium write protected
Memory full
Memory overflow
Meaning: For an AIFF file etc., you attempted to load a file
format that the TRITON series does not support.
Action: If possible, use a computer etc. to convert the data
into a format supported by the TRITON series,
and load it.
Meaning: You attempted to write to a file or to delete a file
that had a read-only attribute.
Meaning: You attempted to save a file to a floppy disk that
contained a read-only file of the same name.
Action: Save the file with a different name.
Meaning: You attempted to load or open a file whose format
was incorrect.
Meaning: When loading a sample file in Disk mode, the file
name specified in the dialog box for selecting a
directory hierarchy or other media did not exist in
the specified location.
Meaning: When executing the Disk mode Utility command
“Delete,” the specified file did not exist.
Meaning: When executing the Disk mode Utility command
“Copy” and you used a wild card to specify the
copy file name, the specified file was not found.
Alternatively, the length of the copy source path
name exceeded 76 characters.
Meaning: In Disk mode when you used the [F6] (“Open”)
key to open a directory, the path length including
the selected directory name exceeded 76 charac-
ters.
Action: Check the file or directory.
Meaning: When executing the Sampling mode function
Sample Edit “Link,” the sample data of the front
sample was also used by the rear sample, and
thus could not be overwritten.
Action: Do not use Overwrite; specify a different sample
as the save destination.
Meaning: The filename that you specified when saving a file
or creating a directory contained invalid charac-
ters.
Action: Change the filename you are specifying. Filena-
mes not permitted by MS-DOS cannot be used as
a filename.
Meaning: You attempted to load a file that was not a Stan-
dard MIDI File.
Meaning: You attempted to load a Standard MIDI File that
was timecode-based.
Meaning: You attempted to load a Standard MIDI File of a
format other than 0 or 1.
Meaning: When loading a Standard MIDI File, the number
of events in a measure exceeded the maximum
(approximately 10,000 events).
Meaning: The attempted edit operation would cause the
maximum number of events in a measure
(approximately 10,000) to be exceeded.
Action: Use event editing etc. to delete unwanted data.
Meaning: When executing the Disk mode Utility “Copy,”
the media was exchanged or ejected, and it was
not possible to copy between separate media on
the same drive.
Meaning: The floppy disk or other media to which you
attempted to save is write-protected.
Action: Turn off write protect on the floppy disk or other
media, and execute the command once again.
Meaning: In Multi mode when editing a multi or pattern,
etc. the total data of all multi has used up all of the
sequence data memory, and further editing is not
possible.
Action: Delete other multi data etc. to increase the amount
of free memory.
Meaning: While realtime recording in Multi mode, there is
no more free memory to accommodate the
recorded data, so recording has been forcibly
halted.
Action: Delete other multi data etc. to increase the amount
of free memory.
Meaning: In Disk mode when loading a Standard MIDI File,
the sequence memory has filled up.
Action: Delete multi data. (If necessary, save the data
before deleting it.)
Meaning: In Disk mode when using “Save Exclusive” to
receive exclusive data, the sequence memory has
filled up.
Action: If you are receiving two or more sets of exclusive
data, transmit them separately to the TRITON-
Rack.
Meaning: In Disk mode, you attempted to load more sample
waveform data than there was free memory
capacity.
Action: In Sampling mode, execute Delete sample to cre-
ate free space in the sample waveform data area,
and re-load the data.
Meaning: Meaning: When you executed the Disk mode
command “Load to Demo Song” or the DEMO/
SNG page “Make Demo Song,” the size of the
demo song data exceeded the capacity of the
Demo Song area.