62
REC/Play: The metronome will sound during recording or
playback.
Off: The metronome will not sound. However, a pre-count
will be heard before recording begins.
Precount [0…2]
Specifies the length of the pre-count when recording.
With a setting of 0, recording will start the instant you press
the [F5] (“START”) key after pressing [F4] (“REC”).
Level [000…127]
Sets the volume of the metronome.
BUS (BUS Select) [L/R, L, R, 1, 2, 3, 4, 1/2, 3/4]
Specifies the output destination of the metronome sound.
L/R, L, R: Output from the OUTPUT (MAIN) L/Mono and/
or R jacks.
1, 2, 3, 4, 1/2, 3/4: Output from the OUTPUT (INDIVIDUAL)
1, 2, 3, 4 jacks respectively.
■ 5.1–1c: REC, START/STOP
Realtime-record or play patterns.
Use the [F4] (“REC”) key and [F5] (“START/STOP”) key to
record.
: Normal mode.
: Press the [F4] (“REC”) key to enter record-
ready mode. To cancel recording, press the [F4] (“REC”) key
once again. In record-ready mode, pressing the [F5]
(“START”) key will start recording. At this time, recording
will begin after counting the number of measures specified
by “Precount.”
If you wish to delete previously-recorded data while you
record, press the [F4] (“REC”) key. Data will be deleted as
long as you continue holding down this key. If you wish to
delete specific data, use “Remove Data” (5.1–1b).
: Playback will start when you press the [F5]
(“START”) key from normal mode.
: Pressing the [F5] (“STOP”) key during
playback will stop playback.
■ 5.1–1d: SW1, SW2
This switches the function of SW1 and SW2 on ( ) or
off ( ). During recording of a pattern/playback, you
can use SW1 and SW2 to control the functions assigned to
them.
■ 5.1–1e: UTILITY
☞ “Memory Status,” “Rename Track” (1.1–1c)
For details on how to select the desired utility function, refer
to “PROG 1.1–1d: UTILITY.”
Rename Pattern
Specifies “Rename Pattern” to access the dialog box, and
rename the selected pattern. You may input up to sixteen
characters. (
☞BG p.38)
Step Recording(Loop)
Here you can perform step recording into a pattern.
This is available when a user pattern is selected.
1 In “Pattern Bank” and “Pattern Select,” specify the pat-
tern. By default, the pattern length is one measure. If you
wish to change the number of measures in the pattern,
set the Utility “Pattern Parameter”.
2 Select the “Step Recording (Loop)” to access the dialog
box.
3 In “Meter,” set the time signature.
This will show the time signature that has already been
set for the measure.
If you change the time signature setting, the time signa-
ture data of the measures you record will change.
4 In “Step (Step Time),” specify the length of the basic step
that you wish to input, in terms of a note value. The
number of clocks in each note value is shown below.
5 In “Duration,” specify the length that the note will actu-
ally be held, relative to the “Step.” In general, 100% will
be tenuto, 85% will be normal, and 50% will be staccato.
6 Use “Vel. (Velocity)” to specify the velocity value (key-
board playing strength) of the note data. When the [F7]
(“PAUSE”) key is pressed, you can hold down the
[ENTER] key and play a note on a connected MIDI
instrument to specify the velocity value. If you set this to
Key, the actual velocity at which you played the key will
be input.
7 Using the keyboard of a connected MIDI instrument or
by selecting parameters at the bottom of the dialog box,
input note events as follows.
• Inputting notes
When you play a note on a connected MIDI instrument,
that note number will be input with the note length that
is specified by
4.
When you press a chord on the keyboard, those note
numbers will be input as chords of the length specified in
4. Since each of the note numbers you press before
releasing all of the keys will be input at the same location,
the notes will be input as a chord even if they are actually
played at different times.
Each time you press and release the keyboard, the loca-
tion will advance by the length specified in
4.
• Inputting rests
Press the [F4] (“Rest”) key to input a rest of the length
specified in
4.
Note numberLocation within the
measure (beat, clock)
Length (beat, clock)
Time signature
Velocity
(0:24)
(0:48)
(0:96)
(1:00)
(2:00)
(4:00)
(0:36)
(0:72)
(0:144)
(1:96)
(3:00)
(6:00)
(0:16)
(0:32)
(0:64)
(0:128)
(1:64)
(2:128)
333333
To Next Page
Loading...
