MULTI
1.1
2.22.33.13.23.33.44.14.24.34.45.16.17.17.27.3
65
In the 5.1: RPPR, RPPR Setup page, RPPR will automat-
ically be on. If you want RPPR to operate in the 1.1:
Play page, check the “RPPR On/Off” check box.
5.1–2a: Control Track,
Control Track [T01…T16: name]
Selects the track that will trigger RPPR. When note data is
received on the MIDI channel of the selected track, the corre-
sponding pattern will play. (
☞1.1–1a)
The program bank, number, and name of the selected track
will be displayed at the right.
(Tempo) [040...240, EXT]
Specifies the playback tempo for RPPR. Refer to “ (Tempo)”
(
☞1.1–1a).
5.1–2b: RPPR Setup
KEY (Key Select) [C#2...C8]
Specifies the key that will trigger an RPPR pattern. The
parameters listed below will apply to the key you specify
here.
You can also select a key by holding down the [ENTER] key
and playing a note on a connected MIDI instrument.
Assign [Off, On]
On (Checked): When you play the key specified by “KEY,”
the pattern selected in “Pat (Pattern Bank),” “Pattern Select”
will be triggered.
Off (Unchecked):The pitch of that key will sound, as in the
normal state of Multi mode.
Pat (Pattern Bank) [Pre (Preset), User]
Pattern Select [P000...149, U00...99]
Selects the RPPR pattern for the key selected in “KEY.” If the
selected user pattern contains no musical data, there will be
no sound when you press that key.
Track [T01…T16: name]
Selects the track that will be used for the RPPR pattern
selected for the “KEY.” When you play the key, the pattern
will be played according to the settings of the track you
select here. Track settings are made in 1.1: Play–4.4: MIDI
Filter4.
Mode [Once, Manual, Endless]
Specifies how the pattern specified for a key will be played
when the corresponding note is played on a connected MIDI
instrument (i.e., when note data is received).
Once: When you press the key, the pattern will playback
only once to the end.
Manual: The pattern will continue repeating as long as you
continue holding the key, and will stop when you release the
key.
Endless: The pattern will continue repeating even after you
release the key. To stop the pattern playback, press any note
below C2, or press the same key once again.
Shift [–12...+12]
Adjusts the playback pitch of the pattern for the specified
“KEY” in semitone steps over a range of ±1 octave. With a
setting of 0, the pattern will be played at its original pitch.
Sync [Off, Beat, Measure, ARP(SEQ)]
Specifies how pattern playback will be synchronized when
the corresponding key is played on a connected MIDI
instrument (i.e., when note data is received).
Off: The pattern will begin playing at the moment you press
the note.
Beat: The pattern will synchronize to the beats of the pattern
that was started by the first key (i.e., the first note-on that
occurs from a condition where no notes of the keyboard are
pressed). This setting is suitable when you wish to play
phrase patterns in unison.
Measure: The pattern will synchronize to the measures of
the pattern that was started by the first key. This setting is
suitable for rhythm, bass or drum patterns.
ARP (SEQ): The pattern will be synchronized to the (quarter
note) timing of the arpeggiator. Use this setting when you
want RPPR to start in synchronization with the arpeggiator.
(
☞BG p.93)
Data compatibility is maintained between the TRITON-
Rack and the TRITON/TRITONpro/TRITONproX
(TRITON keyboard models). On TRITON keyboard
models, setting “Sync” to SEQ allows you to synchro-
nize to the currently-playing song in addition to syn-
chronizing to the arpeggiator.
Data that is set to “ARP (SEQ)” on the TRITON-Rack
will be displayed as “SEQ” in Sequencer mode of the
TRITON keyboard models. Conversely, data that is set
to “SEQ” on TRITON keyboard models will be dis-
played as “ARP (SEQ)” in Multi mode of the TRITON-
Rack.
5.1–2d
5.1–2a
5.1–2b
5.1–2e5.1–2c
Note-on
Note-off
Same key, or C2
Note-off
Once
START STOP
Manual
START STOP
Endless
START STOP
To Next Page
Loading...
